Rinnai FS35 ETR User Manual

Rinnai FS35 ETR

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Flame Fire ETR

Electronic Timer and Remote

Operating and Installation Instructions

Freestanding Royale ETR (Australia)

Timberflame FS35 ETR (New Zealand)

Table of Contents

Customer Instructions

Control Panel Layout 2

Operation 3

Setting the Clock 5

Operating the Timers 6

Error Codes 7

Safety Points 8

Troubleshooting 9

Installation Instructions

Location 10

Flueing 11

Gas Connection 11

Log Installation 12

Testing & Commissioning 13

Technical Data 14

Service Contact Points 14

Wiring Diagram 15

Installation Checklist 16

Installer Details 16

IMPORTANT

This appliance shall be installed in accordance with:

•

Manufacturers Installation Instructions.

• Local Gas fitting regulations.

• Municipal Building codes.

• Gas Installation Code AG5601 / AG601 - NZ 5261.

• Any other relevant statutory regulation.

• This appliance must only be installed, serviced and removed by an

authorised person.

• For Australian installation, this appliance must be installed with

the supplied wire dressguard.

Table of Contents

Questions and Answers:

D
Daniel CardenasJul 31, 2025
Why Rinnai Indoor Fireplace burner will not light?
- D
  Dr. Eric Cole MDJul 31, 2025
  The burner of your Rinnai Indoor Fireplace might not light due to several reasons. It could be due to no power present; ensure the power cord is plugged in and turned on. Another reason could be no gas present; ensure the gas supply is turned on. It could also be due to a power cut; re-ignite after power is restored. Air in the gas pipe may also be a factor, in which case you should purge the air. Finally, it could be due to an ignition failure; repeat the lighting procedure.
W
William JosephAug 10, 2025
What to do if I smell gas from my Rinnai Indoor Fireplace?
- B
  Briana JohnsonAug 11, 2025
  If you smell gas from your Rinnai Indoor Fireplace, it could be due to a gas leak. Immediately turn off the gas at the meter and call your installer.
D
David KimAug 21, 2025
How to fix Rinnai Indoor Fireplace fan not working?
- J
  jamessullivanAug 21, 2025
  If the fan in your Rinnai Indoor Fireplace isn't working, it could be that the heat switch hasn't been activated. Allow the heater to run on HIGH for at least 15 minutes. Alternatively, the fan might not be turned on; make sure the appliance fan switch is in the ON position.

Rinnai FS35 ETR Specifications

General

Model	FS35 ETR
Category	Indoor Fireplace
Type	Direct Vent Gas Fireplace
Fuel Type	Natural Gas or Propane
Venting	Direct Vent
Ignition	Electronic Ignition

Summary

Control Panel Layout

Operation

Heater Operations and Controls

Error Codes

Error Code Interpretation

List of error codes, probable causes, and recommended actions for troubleshooting.

Safety Points

General Safety Precautions

Important safety warnings and guidelines for using the heater safely.

Troubleshooting

Common Symptoms and Solutions

Guide to identifying and resolving common symptoms with their causes and solutions.

Flueing

Flue System Installation

Gas Connection

Gas Supply and Connection

Testing and Commissioning

Installation and Commissioning Procedures

Includes testing, commissioning, checklist completion, and customer instructions.

Wiring Diagram

Heater Wiring Schematic

Installation and Installer Information

Installation Checklist and Installer Details

Related product manuals

Preview: Rinnai Timberflame IB35 ETR

Rinnai Timberflame IB35 ETR

Preview: Rinnai Electric Fire Series

Rinnai Electric Fire Series

Preview: Rinnai Neo

Preview: Rinnai RIB2312

Rinnai RDV700ER

Rinnai RIB2310MN

Preview: Rinnai Neo Series

Rinnai Neo Series

Rinnai SLIMFIRE 25

Rinnai Neo RIB2312N

Rinnai RHFE-1001FA/VA

Preview: Rinnai Symmetry RDV3611

Rinnai Symmetry RDV3611