RKC INSTRUMENT PF Series - Page 85

4. BASIC OPERATION
IMR02L04-E3
4-37
Continued from the previous page.
Name Symbol Data range
Factory set
value
OUT2 assignment
(A continuance)
LOGC2
21: Manipulated output value 1 (MV1)
PID control or Heat/Cool PID control: Heat-side output
[Feedback resistance (FBR) input value when FBR
input is specified with the Position proportioning PID
control.]
22: Manipulated output value 2 (MV2)
Heat/Cool PID control: Cool-side output
Position proportioning PID control: Close-side output
23: Output program value 2
24 to 31: Time signal 1 to Time signal 8
32 to 35: Event 1to Event 4
36: HBA1
37: HBA2
38: Logical OR of HBA1 and HBA2
39: LBA
40: Input error state
41: Program control mode (RUN) state
42: Fixed set point control mode (FIX) state
43: Manual control mode (MAN) state
44: Ramp state
45: Soak state
46: Hold state
47: Wait state
48: Pattern end signal
49: Autotuning (AT) state
50: FAIL state
51: Host communication error
52: Intercontroller communication error
53: Feedback resistance (FBR) input error
Heat/Cool PID
control:
22 or 2
(varies with
output type)
Position
proportioning
PID control:
22
Other control
method:
0 or 20
(varies with
output type)
When the
OUT2 is not
provided: 0
OUT2 transmission output scale high
AHS2
Varies with OUT2 assignment.
Measured value (PV), Set value (SV) monitor:
Input range low to Input range high
Deviation value (DEV):
Input span to Input span
(Within 19999 to 32000 [excluding decimal point])
Output program value 2:
Fixed at 100.0 % (scaling is not available)
Segment time (percentage basis):
Fixed at 100.0 % (scaling is not available)
When using Manipulated output value (MV1 or MV2) as a
transmission output: Fixed at 100.0 % (scaling is not available)
Measured
value (PV),
Set value (SV)
monitor:
Input range
high
Deviation
value (DEV):
 Input span
Other: 100.0
OUT2 transmission output scale low
ALS2
Varies with OUT2 assignment.
Measured value (PV), Set value (SV) monitor:
Input range low to Input range high
Deviation value (DEV):
Input span to Input span
(Within 19999 to 32000 [excluding decimal point])
Output program value 2:
Fixed at 0.0 % (scaling is not available)
Segment time (percentage basis):
Fixed at 0.0 % (scaling is not available)
When using Manipulated output value (MV1 or MV2) as a
transmission output:
Fixed at 0.0 % (scaling is not available)
Measured
value (PV),
Set value (SV)
monitor:
Input range
low
Deviation
value (DEV):
 Input span
Other: 0.0
Function block 33 (F33.01 to F33.03)
OUT3 assignment
LOGC3
The data range is same as OUT2 assignment.
However, No. 7 or 23 becomes output program value 3.
There are no relay contact output and triac output in OUT3
No control output when No. 21 or 22 is selected at Position
proportioning PID control.
0 or 20
(varies with
output type)
When the
OUT3 is not
provided: 0
OUT3 transmission output scale high
AHS3
Varies with OUT3 assignment.
The data range is the same as the OUT2 transmission output scale high.
Continued on the next page.