Robe ROBIN T1 PC - 7.6 Service Tab and Calibration

30
Play Program 2 - The option starts user program No. 2.
Play Program 3 - The option starts user program No. 3.
Edit Program - Use the menu to create or to edit desired program. The xture o󰀨ers 3 free programs, each
up to 80 steps.
Edit Program 1 - The option allows to edit user program No.1.
Edit Program 2 - The option allows to edit user program No.2.
Edit Program 3 - The option allows to edit user program No.3
To edit program:
1. Touch the item which you want to edit (“Edit Program 1” - “Edit Program 3”).
2. Touch the item "Edit Program Steps".
3. Touch the item "Step 1".
4 From the list of e󰀨ects touch desired e󰀨ect and set its value. Browse throw the list by touching the [up arrow]
and [down arrow] and set all desired e󰀨ects.
An item "Step Time" (value of 0-25.5 sec.) is the time during which e󰀨ects last in the current step
5. Save adjusted e󰀨ects to the current step by touching the [conrm] or save and copy them to the following
step by touching the [conrm+copy]. By touching the text box "Preview" next to the current program step you
can view created scene.
6. Repeat the steps 4 and 5 for next program steps.
7. After editing desired program steps, adjust the length of the program by touching the text boxes "Start Step"
and "End Step".
Meaning of the icons used in the "Edit Program" menu:
- moves down on the next page - saves adjusted values and leaves menu
- moves up on the previous page - saves values to the current step and copy them to the
following prog. step
- leaves menu without saving values
7.6 Tab "Service"
Adjust DMX Values - The menu allows you to set all e󰀨ects to desired positions before ne calibration of the
e󰀨ects .
Calibrations - This menu enables ne calibration of xture e󰀨ects and download default calibration values.
Calibrate E󰀨ects - The menu allows the ne adjustment of e󰀨ects.
Pan- a pan position ne adjustment (value range: 0-255)
Tilt - a tilt position ne adjustment (value range: 0-255)
Zoom - a zoom module ne movement (value range: 0-255)
Focus - a focus module (colour edge correction) ne movement (value range: 0-255)
Frost 1/1 - a light frost ne position movement 1 (value range: 0-255)
Frost 1/2 - a light frost ne position movement 2 (value range: 0-255)
Frost 2/1 - a medium frost ne position movement 1 (value range: 0-255)
Frost 2/2 - a medium frost ne position movement 2 (value range: 0-255)
Barndoors rotation - a ne rotation of the barndoors module (value range: 0-255)
Barndoor 1 move - a ne movement of the barndoor 1 (value range: 0-255)
Barndoor 2 move - a ne movement of the barndoor 2 (value range: 0-255)
Barndoor 3 move - a ne movement of the barndoor 3 (value range: 0-255)
Barndoor 4 move - a ne movement of the barndoor 4 (value range: 0-255)
Scrim positioning - a ne positioning of the scrim (value range: 0-255)
Scrim indexing - a ne rotation of the scrim (value range: 0-255)
Calibration of the eects via the control board
1. Disconnect DMX controller from the xture and enter the "Calibrate E󰀨ects" menu.
2. Use the [up arrow] and [down arrow] to nd "Pan" and touch it to enter the ne e󰀨ect adjustment screen.
3. Set desired value and save it by touching the [conrm].
4. Repeat steps 2 and 3 for next item
5. After calibrating all e󰀨ects, touch the [conrm] to save all adjusted values and reset the xture.
Calibration of the eects via the DMX controller
1. Connect DMX controller to the xture and enter the "Calibrate E󰀨ects" menu.