What to do if Robomow RM510 displays 'Check signal Press GO'?
J
Jodi ButlerAug 30, 2025
The Robomow Lawn Mower displays 'Check signal Press GO' because there is no fitting between the 'Signal type' setting and the signal jumper, automatic operation is initiated outside the perimeter wire, the perimeter wire is connected with the wrong polarity, or there's signal interference. Set the 'Signal type' menu to 'A' and confirm the jumper is installed, or set it to 'B' and remove the jumper. Place the mower inside the lawn. Change the wires connected to the plot connector. Call service for help in case of signal interference.
M
Michelle BowenSep 6, 2025
Why is my Robomow RM510 Lawn Mower operating at the wrong times?
D
Dylan BautistaSep 7, 2025
If the Robomow Lawn Mower is operating at the wrong times, first confirm that the time (hour and date) is set correctly. Also, check if the ‘GO’ button was unintentionally pressed. To prevent this, activate the ‘Child guard’ or ‘Anti-theft’ options, which require multiple button presses to start the operation.
A
ashley64Aug 29, 2025
What to do if Robomow Lawn Mower displays 'Bumper pressed'?
M
Michael WhiteAug 29, 2025
The Robomow Lawn Mower displays 'Bumper pressed' because the bumper is constantly being pressed. Move the mower away from the object pressing against the bumper.
A
Amanda CoxSep 16, 2025
What to do if Robomow Lawn Mower displays 'Rain detected start delayed'?
R
raypatriciaSep 17, 2025
If Robomow Lawn Mower displays 'Rain detected start delayed', it means the operation is delayed due to rain. The message disappears when Robomow doesn't detect rain for x hours (defined in ‘Delay after rain’ menu).
C
Christopher CastilloSep 8, 2025
What to do if Robomow Lawn Mower displays 'Check mow height'?
E
Elizabeth WoodsSep 8, 2025
The Robomow Lawn Mower displays 'Check mow height' because the mowing motor has faced over-current due to high grass or an obstacle around the blade, or something is preventing the blade from rotating. Remove the fuse before lifting the mower. Inspect blades for debris and clean out accumulated grass using a wooden stick.
J
Johnny VaughanSep 12, 2025
What to do if Robomow Lawn Mower displays 'Rain detected Press GO'?
K
keykevinSep 12, 2025
The Robomow Lawn Mower displays 'Rain detected Press GO' because it has skipped the last depart due to rain detection. Change the setting of the ‘Rain sensor’ to ‘off’ under the ‘Settings’ menu if you choose to override the rain sensor.
T
Tracy AguilarSep 15, 2025
What to do if Robomow RM510 displays 'Peg base then press GO'?
Z
zimmermanlaurenSep 15, 2025
The Robomow Lawn Mower displays 'Peg base then press GO' after the ‘Base position’ test is completed successfully. Fasten the base in place using the 2 stakes.
S
stephaniefreemanSep 23, 2025
What to do if Robomow Lawn Mower displays 'Time completed'?
J
Joseph MartinSep 23, 2025
The Robomow Lawn Mower displays 'Time completed' when the operating time set for that zone has been reached. Connect to the charger if all mowing has been completed for the day.
S
Shirley FrazierAug 26, 2025
What to do if Robomow RM510 Lawn Mower displays 'Check power (Base Station)'?
J
Jamie WilliamsAug 26, 2025
The Robomow Lawn Mower displays 'Check power (Base Station)' because the power supply is not plugged in properly, there's no power to the receptacle, the contacts are dirty, or charging isn't detected. Confirm the power supply is plugged into the main power receptacle and that the main power is on. Clean the contacts with a brush or cloth. Also, confirm a good connection of the power supply and the Base Station board cables.
M
Michael CohenAug 25, 2025
What to do if Robomow Lawn Mower displays 'Check wire'?
G
gibsonerinAug 26, 2025
The Robomow Lawn Mower displays 'Check wire' due to a poor connection of the perimeter wire or the wire is too long. Check and repair all loose, poor, or corroded connections using the waterproof connectors supplied in the box. If the wire is longer than 500m, split the area into 2 separate zones.
To Next Page
General
