EasyManua.ls Logo

Robomow RL2000 - User Manual

Robomow RL2000
84 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating & Safety Manual
RL MODELS
WWW.ROBOMOW.COM / WWW.ROBOMOW.EU
DOC0100F

Table of Contents

Questions and Answers

  • J
    Jamie MartinAug 18, 2025
    What to do if my Robomow Lawn Mower shows 'Check Power'?
    • B
      Bradley BlackburnAug 18, 2025
      If your Robomow lawn mower displays a 'Check Power' message, ensure the power supply/charger is properly plugged into the main power supply and that the charging plug is fully inserted into the mower's charging socket. A temporary power loss might have occurred; disconnect and reconnect the charging plug. Also, check if there is power to the receptacle or if the main power is shut off. Ensure the mower contacts touch the base station contacts, and that the contacts are clean. Confirm a good connection of the cables to the Base Station contacts and check the Charging fuse 5A.
  • D
    davidlloydAug 21, 2025
    What to do if my Robomow RL2000 displays 'Front Wheel Problem'?
    • J
      Juan HernandezAug 21, 2025
      If your Robomow displays a 'Front Wheel Problem' message, it could be due to several reasons. The front wheel may have left the ground for too long. The Robomow might have driven onto an obstacle, raising the front end; remove the obstacle. The Robomow could be used on a slope too steep; exclude this area from mowing. High grass might be preventing the front wheel from fully riding on the ground; raise the cutting height. Also, the ground might contain large holes; fill these areas with dirt and level off.
  • S
    Sandra McgeeAug 23, 2025
    Why does my Robomow RL2000 Lawn Mower show 'Check Mow Height'?
    • J
      jason53Aug 23, 2025
      If your Robomow lawn mower displays a 'Check Mow Height' message, it indicates that the mowing motors have faced over-current for too long, or an obstacle is stuck or wrapped around the blades. Remove the power pack before lifting the mower and inspect the blades for foreign material or debris preventing rotation. Clean out accumulated grass clippings using a wooden stick. Something might be preventing a blade from rotating freely, such as severe grass accumulation or a rope wrapped around the mowing blade. An object might be jammed under the mower preventing blade from rotating.
  • A
    April ScottAug 26, 2025
    What does error 'B' mean on my Robomow RL2000 Lawn Mower?
    • M
      madamsAug 26, 2025
      Error 'B' on your Robomow Lawn Mower indicates that the bumper was pressed during warm up, for >2 sec during manual mowing, or while departing from the Base Station. Move the mower away from any obstacle pressing on the bumper. If in manual mowing mode, manually drive the mower away from the obstacle.
  • B
    Brian LuceroAug 27, 2025
    What does 'Check P. Switch' mean on my Robomow RL2000?
    • E
      Emily HenryAug 27, 2025
      If your Robomow Lawn Mower displays 'Check P. Switch', it means the mower is trying to depart from the Base Station and the perimeter switch is not responding or there is a perimeter wire disconnection detected at departure time. Turn on the perimeter switch and check for broken wire warning.
  • M
    Miguel HoustonAug 30, 2025
    What does 'Drive Overload Cooling Wait…' mean on my Robomow RL2000?
    • H
      holmescodyAug 30, 2025
      If your Robomow lawn mower displays 'Drive Overload Cooling Wait…', it means the drive motors have been working under a severe load for too long. There is no need to do anything – Robomow will automatically renew the operation as the drive motor cools down.
  • A
    Adam HarrisSep 1, 2025
    What does error 'H' mean on my Robomow RL2000?
    • R
      Rose LewisSep 1, 2025
      Error 'H' on your Robomow lawn mower indicates that the theft guard system is activated. Enter the correct 4-digit code. ‘Theft Guard’ can be deactivated under ‘User Preferences’.
  • E
    Elizabeth GarzaSep 3, 2025
    What does 'Low temp. Waiting…' mean on my Robomow Lawn Mower?
    • R
      ramossarahSep 4, 2025
      If your Robomow lawn mower displays 'Low temp. Waiting…', it means Robomow is charged through the Base Station and the ambience temperature is out of range (below 32ºF / 0ºC). Do not do anything, the charging is stopped and Robomow is waiting for temperature to change back to the allowed range; if temperature stays out of the range for more than 12 hours, the message is changed to ‘Low temp. Press HP.
  • D
    Danielle DrakeSep 6, 2025
    What does error 'C' mean on my Robomow RL2000?
    • R
      Renee Navarro MDSep 6, 2025
      Error 'C' on your Robomow lawn mower is displayed on first use only. Follow the prompts on the LCD screen to calibrate the mower.
  • B
    Brittany ChambersSep 8, 2025
    What does 'Low temp. Disc. charger' mean on my Robomow Lawn Mower?
    • D
      Debra HarrisSep 8, 2025
      If your Robomow lawn mower displays 'Low temp. Disc. charger', it means Robomow is charged through the plug and ambience temperature is out of range (below 32 ºF / 0 ºC). Robomow charging is not allowed when the ambience temperature is going down below 32ºF / 0ºC; Disconnect the charger plug and wait until the temperature will go up or take the Robomow to be charged in a warmer place.

Summary

Robomow Operating & Safety Manual

Introduction and Safety Information

Covers the welcome, important safety notes, and general warnings.

Warning Decal Definitions

Explains the meaning of various safety symbols and decals on the mower.

Robomow - Safety Features

Details the built-in safety mechanisms of the Robomow mower.

Chapter 1 Planning

Base Station Location and Power Supply

Determining optimal placement for the Base Station and its power supply.

Perimeter Wire Layout Planning

Planning the path of the perimeter wire for lawn boundaries.

Chapter 2 Base Station and Perimeter Wire Setup

Perimeter Wire Setup Procedures

Detailed steps for setting up the perimeter wire, including special cases.

Fastening Perimeter Wire and Completing Setup

Base Station Assembly and Placement

Instructions for assembling and positioning the Base Station.

Testing and Non-Base Zone Setup

Finalizing Setup and Testing

Chapter 3 Preparing Robomow

Initial Setup and Calibration

Procedures for inserting the power pack fuse and calibrating the mower.

Cutting Height and Ground Clearance Adjustment

Chapter 4 The mowing process

Operation Safety and Basic Driving

Safety guidelines and instructions for driving the Robomow manually.

Chapter 5 Setting the Weekly Program (RL2000 only)

Setting Up the Mowing Schedule

Programming the weekly mowing times and days for automatic operation.

Setting Current Time and Canceling Days

Chapter 6 Charging

Charging Methods and Procedures

Chapter 7 Setting Robomow and Advanced Features

Manual User Options and Settings Navigation

Advanced Settings Configuration

Entry Points Setup and Management

Chapter 8 Troubleshooting

Error Messages and Messaging

Interpreting system messages and error codes for fault diagnosis.

Problem Diagnosis by Category

Troubleshooting common issues related to Base Station, Perimeter Switch, and operation.

Chapter 10 Maintenance and Storage

Maintenance Schedule and Procedures

Winter Storage Guidelines

Robomow RL2000 Specifications

General IconGeneral
TypeRobotic lawn mower
Cutting width530 mm
Cutting system-
Recommended lawn area2000 m²
Maximum cutting height63 mm
Minimum cutting height26 mm
Grass collecting volume- L
Power sourceBattery
Charging time20 h
Battery voltage24 V
Battery capacity17 Ah
CordlessYes
Weight and Dimensions IconWeight and Dimensions
Depth890 mm
Width665 mm
Height315 mm
Weight23700 g

Related product manuals