Roland BK-3 - Almindelig Brug Af; Tænd for; Lyt Til Demosange På

16 QUICK GUIDE
ALMINDELIG BRUG AF BK-3
Tænd for BK-3
1. Skru ned for [VOLUME] knappen ved at dreje knappen helt mod uret.
2. Tryk på [POWER] knap for at tænde BK-3.
3. Skru op for [VOLUME] knappen ved at dreje knappen med uret indtil det ønskede
styrkeniveau.
Lyt til Demo sange på BK-3
Tryk samtidig på knapperne [Menu] og [Exit]
BK-3 spiller en Demo Song og du introduceres for de vigtigste muligheder på
instrumentet.
Tryk på [Exit] knappen for at forlade demofunktionen.
Before You Start Using BK-3
16
Installing the Music Rest
1. Install the music rest as shown in the illustration.
NOTE
When moving the BK-3, be sure to remove the music rest as a
safety precaution.
NOTE
Do not apply excessive force to the music rest.
NOTE
The music rest is not designed to accept the placement of
laptops or other heavy objects.
Turning the Power On/O
Once everything is properly connected (See “6. Before You Start Using
BK-3” p. 14), be sure to follow the procedure below to turn on their
power. If you turn on equipment in the wrong order, you risk causing
malfunction or equipment failure.
Turning the Power On
1. Turn the [VOLUME] knob all the way to the left to
minimize the volume
NOTE
Before turning the BK-3 on/o, always be sure to turn the
volume down. Even with the volume turned down, you might
hear some sound when switching the BK-3 on/o.
However, this is normal and does not indicate a malfunction.
2. Press the [POWER] switch to turn on the power.
The power will turn on, an opening message will appear in the
BK-3’s screen, and then the main page will appear.
After a brief interval, the BK-3 will be ready to produce sound.
3. Use the [VOLUME] knob to adjust the volume.
NOTE
This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
Turning the Power O
1. Turn the [VOLUME] knob all the way to the left to
minimize the volume.
NOTE
Never switch o the BK-3 while playback or recording is running
or while data are being read from, or written to, an external USB
memory.
2. Press the BK-3’s [POWER] switch.
The display will go dark and the power will turn o.
NOTE
If you need to turn o the power completely, rst turn o the
[POWER] switch, then unplug the power cord from the power
outlet. Refer to “Connecting the AC Adaptor” on p. 14
On
O
If you don’t want the power to turn o
automatically, turn the “Auto O” setting o !
With the factory settings, the unit’s power will automati-
cally be switched o 30 minutes after you stop playing or
operating the unit.
Shortly before the BK-3 shuts down automatically, the display
starts counting down the seconds. If you want to keep using
the BK-3 at this stage, press any button. When the BK-3 is
turned o by the “Auto O” function, the [POWER] button’s
position doesn’t change, which means that you need to press it
once, wait a few seconds, then press it again to switch the BK-3
back on.
If you don’t want the power to turn o automatically, change
the “Auto O” setting to “OFF” as described on p. 52.
Before You Start Using BK-3
16
Installing the Music Rest
1. Install the music rest as shown in the illustration.
NOTE
When moving the BK-3, be sure to remove the music rest as a
safety precaution.
NOTE
Do not apply excessive force to the music rest.
NOTE
The music rest is not designed to accept the placement of
laptops or other heavy objects.
Turning the Power On/O
Once everything is properly connected (See “6. Before You Start Using
BK-3” p. 14), be sure to follow the procedure below to turn on their
power. If you turn on equipment in the wrong order, you risk causing
malfunction or equipment failure.
Turning the Power On
1. Turn the [VOLUME] knob all the way to the left to
minimize the volume
NOTE
Before turning the BK-3 on/o, always be sure to turn the
volume down. Even with the volume turned down, you might
hear some sound when switching the BK-3 on/o.
However, this is normal and does not indicate a malfunction.
2. Press the [POWER] switch to turn on the power.
The power will turn on, an opening message will appear in the
BK-3’s screen, and then the main page will appear.
After a brief interval, the BK-3 will be ready to produce sound.
3. Use the [VOLUME] knob to adjust the volume.
NOTE
This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
Turning the Power O
1. Turn the [VOLUME] knob all the way to the left to
minimize the volume.
NOTE
Never switch o the BK-3 while playback or recording is running
or while data are being read from, or written to, an external USB
memory.
2. Press the BK-3’s [POWER] switch.
The display will go dark and the power will turn o.
NOTE
If you need to turn o the power completely, rst turn o the
[POWER] switch, then unplug the power cord from the power
outlet. Refer to “Connecting the AC Adaptor” on p. 14
On
O
If you don’t want the power to turn o
automatically, turn the “Auto O” setting o !
With the factory settings, the unit’s power will automati-
cally be switched o 30 minutes after you stop playing or
operating the unit.
Shortly before the BK-3 shuts down automatically, the display
starts counting down the seconds. If you want to keep using
the BK-3 at this stage, press any button. When the BK-3 is
turned o by the “Auto O” function, the [POWER] button’s
position doesn’t change, which means that you need to press it
once, wait a few seconds, then press it again to switch the BK-3
back on.
If you don’t want the power to turn o automatically, change
the “Auto O” setting to “OFF” as described on p. 52.