Roland Camm-1 GR2-540 - User Manual

Thank you very much for purchasing this product.
• To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual com-
pletely and store it in a safe location.
• Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.
• The specifications of this product and the contents of this operation manual are subject to change without notice.
• The operation manual and the product have been prepared and tested as much as possible. If you find any misprints or errors, please
inform us.
• Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur through use of this product,
regardless of any failure to perform on the part of this product.
• Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur with respect to any article made
using this product.
FA02570
R1-210707
http://www.rolanddg.com/
Copyright © 2021 Roland DG Corporation

Summary

Preparations before Cutting Output

Recommended Cutting Conditions

Performing a Cutting Test

Adjusting the Cutting Conditions

Covers adjusting blade force, speed, and offset for precise cutting.

Basic Cutting

Basic Printing and Cutting

Automatic Aligning System (AAS)

Details on the AAS for accurate alignment of print and cut.

Setting Crop Marks in Cutting Data

Instructions for setting crop marks using AAS plug-ins and GreatCut-R.

Printing Cutting Data on Material

Performing Cutting

Guides for sending print-and-cut jobs from various software.

Using GreatCut-R

Setting Up Cutting by Layer

Optimizing the Output Quality

Dealing with Material Thickness;Hardness (Softness)

Overlap Cutting

Preventing and Correcting Misaligned Cutting

Addresses issues causing misalignment and ensures accuracy.

Cutting Efficiently

Using Presets

Reducing Cutting Output Time

Optimizes cutting speed and acceleration for faster job completion.

Maintenance

Cleaning and Replacing Consumable Parts

Guides on cleaning the machine and replacing worn parts.

AAS Offset Test

Running an AAS Offset Test

Procedure for conducting an offset test for AAS sensor accuracy.

Adjusting the AAS Offset

Steps to correct deviations found during the AAS offset test.

Machine Problems

The Machine Doesnt Run

Troubleshooting steps for when the machine fails to operate.

Cutting Data Cannot Be Sent from the Operation Application

Resolves issues related to data transmission errors.

Cutting Output Problems

Crop Marks Are Not Detected

Solutions for when the machine fails to detect crop marks.

Material Feeding Is Not Smooth

Addresses issues related to unstable or improper material feeding.

The Material Slips Away from the Pinch Rollers during Cutting

Material Lifts Up during Cutting and Gets Damaged by Blade

Output Quality Problems

Printing and Cutting Are Misaligned

Diagnoses and resolves misalignment between printed graphics and cuts.

Uncut Areas Remain or Cut Edges Are Not Clean

Addresses issues with incomplete cuts or unclean edges.

The Machine Cuts the Carrier Paper

Misaligned Cutting Start and End Points

Messages on the Operation Panel

Error Messages

Details error messages and their corresponding troubleshooting actions.

Roland Camm-1 GR2-540 Specifications

General

Connectivity	USB 2.0, Ethernet
Cutting Method	Media-moving method
Power Supply	AC 100 to 240 V ±10%, 50/60 Hz
Power Requirements	AC 100 to 240 V ±10%, 50/60 Hz
Cutting Width	54 inches
Maximum Cutting Speed	1, 485 mm/s
Software Resolution	0.025 mm/step
Weight	187 lbs
Usable Tools	Cutting blade, plotting pen
Distance Accuracy	±0.2% or 0.3 mm (0.012 in), whichever is greater
Repeatability Accuracy	±0.1 mm
Alignment Accuracy for Print & Cut	±0.04 inches
Operating Temperature	41-95°F (5-35°C)
Operating Humidity	35 to 80% RH (non-condensing)
Weight (with stand)	187 lbs
Blade Type	Roland CAMM-1 series blades
Resolution	0.025 mm/step