Roland R-8M - Page 125

MIDI Implementation
Ottpn LSB
Siatus
Bnll
ORPN MSB
OOata Entry
Soms
BnH
jtoxind Third
64H 111!
Sialu?
Second
Third
BnH
65H
mmH
gecond
06H
Third
vvH
n-MIDI channel : OH
-
Fll (0
-
15)
0-ch.l I5"ch.l6
II
-
The lower byte of the paramder number
designated
by
RPN
mm
-
The upper byte of
the parameter number designated by RPN
vv
-
The value of the parameter designated by RPN
The R-8M
receives
the message on the
channel set
by
PATCll/PFM/BASIC/
Receive
Ch.
Z3R«caiva Mouagat to Control th« System
Chann*)
Voio*
M«1U9*
9
Program ehing*
Suius Second
CnH PPH
n
•
MIDI channel
pp
-
Program
number
;0H
-
FH (0
-
15) 0-Ch.l I5-ch.lC
T OOH
-
7FH (0
-
127)
The
R-8M
receives the message on the channel set by SETUP/MIDl/Control Ch.
Upon receiving this message with SETUP/MIDI/Pgm Change
-
ON selected, the K
-
8M changes Patch
and Feel Patch according to the program change map's contents
set by the SETUP/PGM.
[Svatam Common Mams*
tSons potition pointer
Parameters of a unit can be
changed
by using MIDI RPN'
function. De^gnaie Ihe
parameter to be changed by a set of RPN MSB
and
l-SB.
and then specify the
now
parameter
value with
Data Entry.
Effective
RPN
for the R-8M is Pitch Bend
Sensitivity
(RP,\ «0) only.
Status
F2H IIH
mm.ll
-
Song position
Hud
mmH
: OOH,O0H
-
7FH,7F1I (0
-
16383)
This message syncs the Groove to the play information when FEEL/RliGL/Regular
-
GROOVE has been selected.
MSB I .SB Rata entry
Description
OOH
001! vvH Piidi bend
sensitivity
vv
» 0-
12 semitone steps, up to I
octave
Upon receiving this message. Ihe R-8M rewrites PATCH/PFM/BASIC/Bend Range
With the received value.
Syitam R*«l Tim* Maius*
•Timing clock
Sl^t^is
F8H
tPitch
B«nd Ching*
Status
Second
Thifd
Enil III! mmH
Status
FAH
n
-
MIDI
channel
mm.H
•=
\'alue
:
OH
-
Fll
(0
-
15) "
ch.l 15
-
ch.l6
:0OH,0OH
-
7FII,7KH
{-8192
-
*819l)
The R
-
8M receives Ihe message on the channel set by PATCH/PFM/BASIC/
Receive Ch.
Upon
receiving
this message
with SETUP/MIDl/Pitch
Bender
»
ON
selected, the
R
-
8M bends the pitch
of sounding note according to the value
set by
PATCH/PI'M/
BASiC/Bend Range.
Channal Moda MaiNga
#R*Mt all controllara
#Continua
Status
FBK
•Stop
Status
FCH
These messages syncs the groove to the play information
when
FEEL/REGL/Regular
=
GROOVE has been selected.
gtalus
SsSfiDi!
Tti'"!
BnH 79H OOH
n
<
MIDI channel :0H
-
Fll CO
-
15) 0-cIi.l
15-ch.l6
The
R
-
8M
receives
the message
on the channel set by PATCH/PFM/BASIC/
Receive Ch.
The R
-
SM initializes all controllers upon receiving this message.
Pitch Bend Change ± (center)
Panpot Off (PATCH/PFM/SOUND/Out Asgn is
activated)
Hold 1
Modulation -iOH (the offset of assigned parameter becomes 0.)
•
All notvi
otr
Status Second
Uuc!
BnH 7BH OOH
n
=
MIDI channeNOH
-
FH (0
-
15)
0-ch.i I5"ch.i6
The R
-
8M
receives the message on the channel set by
PATCH/PFM/BASIC/
Receive Ch.
Mutes the
sounding notes upon receiving an
All Nutcs OH message.
(Activa Mnaing
FEH
Whenever
the R-8M receives this message, it monitors
the interval of the coming data.
If the subsequent message has not
arrived
300 ms
after the previous data, it processes
all sections as though it has received an All Notes Off message
and a
Reset
All
Controllers message. Monitoring of incoming
signals is terminated.
Sy*t*m Exctutiv* M««Mga
Status
FOH : System
Exclusive
F7H : EOX
(End
Of
Exclusive)
With the R
-
8M, the System Exclusive Message can be used to
transmit and receive
parameters Of Paldi. Feel Patch and Setup.
For details refer to "Roland
Exclusive
Messages"
and paragraph 3.
123