Roland SPD-SX PRO - Warm Saturator

Effect List (English)
192
Warm Saturator
This is a variety of saturator, and is distinctive for its warmer sound.
Parameter
Value
Explanation
EQ Low Frequency
20–16000 [Hz]
Input filter (low range)
Boosts/cuts the sound below the specified frequency.
EQ Low Gain
-24–+24 [dB]
Amount of boost/cut
EQ High Slope
THRU, -12dB, -24dB
Input filter (high range)
Amount of attenuation per octave
THRU: No attenuation
-12 dB: gentle
-24 dB: steep
EQ High Frequency
20–16000 [Hz]
Input filter (high range)
Attenuates frequencies that are higher than the specified frequency.
DrvPre Type
THRU, LPF, HPF, LSV, HSV
Types of filter that precedes the distortion processing
THRU: No filter is applied
LPF: A filter that passes the sound below the specified frequency
HPF: A filter that passes the sound above the specified frequency
LSV: A filter that boosts/cuts the sound below the specified frequency
HSV: A filter that boosts/cuts the sound above the specified frequency
DrvPre Frequency
20–16000 [Hz]
Frequency at which the pre-distortion filter operates
DrvPre Gain
-24.0–+24.0 [dB]
For the LSV/HSV types, the amount of boost/cut
Drive
0.0–+48.0 [dB]
Strength of distortion
DrvPost1 Type
THRU, LPF, HPF, LSV, HSV
Type of filter 1 which follows the distortion processing
DrvPost1
Frequency
20–16000 [Hz]
Frequency at which post-distortion filter 1 operates
DrvPost1 Gain
-24.0–+24.0 [dB]
For the LSV/HSV types, the amount of boost/cut
DrvPost2 Type
THRU, LPF, HPF, LSV, HSV
Type of filter 2 which follows the distortion processing
DrvPost2
Frequency
20–16000 [Hz]
Frequency at which post-distortion filter 2 operates
DrvPost2 Gain
-24.0–+24.0 [dB]
For the LSV/HSV types, the amount of boost/cut
DrvPost3 Type
THRU, LPF, HPF, BPF,
PKG
Type of filter 3 which follows the distortion processing
THRU: No filter is applied
LPF: A filter that passes the sound below the specified frequency
HPF: A filter that passes the sound above the specified frequency
BPF: A filter that passes only the specified frequency
PKG: A filter that boosts/cuts the specified frequency
DrvPost3
Frequency
20–16000 [Hz]
Frequency at which post-distortion filter 3 operates
DrvPost3 Gain
-24.0–+24.0 [dB]
For the PKG type, the amount of boost/cut
DrvPost3 Q
0.5–16.0
Width of the frequency range affected by the filter
Makeup Sense
-60.0–0.0 [dB]
Adjust this value so that the sound is not made louder when distortion is
applied.
DrvPost Gain
-48.0–+12.0 [dB]
Gain following distortion processing
Drive Balance (*1)
D100:0W–D0:100W
Volume balance between the dry sound (D) and effect sound (W)
Level
0–127
Output Level
*1: This parameter corresponds to MFX Ctrl. For details, refer to “De MFX bedienen met de PAD EDIT [1] [2]-regelaars (MFX
Ctrl)(P.204)”.
*1: This parameter corresponds to MASTER EFFECT CTRL. For details, refer to “Het MASTER EFFECT bedienen met de MASTER
EFFECT-regelaar (MASTER EFFECT CTRL)(P.205)”.