Roland TR-6S - Main Screens; PTN SELECT Screen; TR-REC Screen; STEP LOOP Screen

10
INST Parameters
Parameter Value Explanation
DrvPstH
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the high-frequency level of the
EQ that is applied after distorting the
sound.
CRUSHER
Balance
INST [CTRL] *3
OFF, 1–255
Adjusts the lo-fi effect.
With a setting of 255, the lo-fi effect is at
100%.
SampleRate
0–255
Specifies the sampling frequency at which
CRUSHER resamples the sound.
Higher settings of SampleRate lower the
sampling frequency, producing a more
lo-fi sound.
Filter
0–255
Specifies the cutoff frequency of the LFP
that is applied before CRUSHER resamples
the sound.
By lowering the Filter value, you can
reduce harsh high-frequency noise.
SATURATOR
PreType
Type of filter that precedes the distortion processing
THRU No filter is applied
LPF
A filter that passes the sound below the
specified frequency
HPF
A filter that passes the sound above the
specified frequency
LSV
A filter that boosts/cuts the sound below
the specified frequency
HSV
A filter that boosts/cuts the sound above
the specified frequency
PreFreq
20–16000 [Hz]
Frequency at which the pre-distortion
filter operates
PreGain
-24–24 [dB]
For the LSV/HSV types, the amount of
boost/cut
Drive
INST [CTRL] *3
0–48 [dB] Strength of distortion
Post1Type
THRU, LPF, HPF,
LSV, HSV
Type of filter 1 which follows the distortion
processing
Post1Freq
20–16000 [Hz]
Frequency at which post-distortion filter
1 operates
Post1Gain
-24–24 [dB]
For the LSV/HSV types, the amount of
boost/cut
Post2Type
THRU, LPF, HPF,
LSV, HSV
Type of filter 2 which follows the distortion
processing
Post2Freq
20–16000 [Hz]
Frequency at which post-distortion filter
2 operates
Post2Gain
-24–24 [dB]
For the LSV/HSV types, the amount of
boost/cut
Post3Type
Type of filter 3 which follows the distortion processing
THRU No filter is applied
LPF
A filter that passes the sound below the
specified frequency
HPF
A filter that passes the sound above the
specified frequency
BPF
A filter that passes only the specified
frequency
PKG
A filter that boosts/cuts the specified
frequency
Post3Freq
20–16000 [Hz]
Frequency at which post-distortion filter
3 operates
Post3Gain
-24–24 [dB] For the PKG type, the amount of boost/cut
Post3Q
0.5–16.0
Width of the frequency range affected by
the filter
Sense
-60–0 [dB]
Adjust this value so that the sound is not
made louder when distortion is applied.
PostGain
-48–12 [dB] Gain following distortion processing
Parameter Value Explanation
Balance
OFF, 1–255
Volume balance between the dry sound
(D)
and effect sound (W)
Level
0–255 Output Level
FREQ SHIFT
Freq
INST [CTRL] *3
-8.0–0–8.0 [kHz] Shifts the frequency in a wide range.
Fine
-500–0–500 [Hz] Shifts the frequency in a narrow range.
Balance
OFF, 1–255
Volume balance between the dry sound
(D)
and effect sound (W)
RING MOD
Freq
INST [CTRL] *3
0–8, 000 [Hz] Shifts the frequency in a wide range.
Fine
-128–0–127 [Hz] Shifts the frequency in a narrow range.
Balance
OFF, 1–255
Volume balance between the dry sound
(D)
and effect sound (W)
SPREAD
Rate
INST [CTRL] *3
OFF, 0.2–200 [Hz] Rate of spread
Mode
SHIFT Converts left/right in different directions.
RING
Converts left/right by different
frequencies.
Balance
OFF, 1–255
Volume balance between the dry sound
(D)
and effect sound (W)
*3 If you set the KIT: CTRL Sel parameter to InstFX, you can use the [CTRL]
knobs of the instrument edit section to control this.