Roland TR-6S - INST Parameters; INST

7
INST Parameters
INST
Parameter Value Explanation
Common to all tones
Tune
[TUNE]
-128–0–+127 Adjusts the tuning (pitch).
Decay
[DECAY]
0–255 Adjusts the length of the decay.
Level
INST Level Slider
0–255
Specifies the level.
* This parameter changes when you
operate each instrument’s level slider.
* This adjusts the level of the sound after it
has passed through INST FX.
Gain
-40.0dB–0.0dB–
+40.0dB
(steps of 0.5 dB)
Specifies the gain.
* This adjusts the level of the sound after it
has passed through INST FX.
Pan
L127–CENTER–
R127
Specifies the stereo position.
ReverbSend
0–255 Adjusts the level that is sent to reverb.
DelaySend
0–255 Adjusts the level that is sent to delay.
LFO
Tune, Decay, Level,
Pan, ReverbSend,
DelaySend, InstFX,
(BD) Attack
(SD) Snappy
(TOM) Color
(SAMPLE) Coarse,
Rate, Spread,
BitReduce, Attack,
HoldMode,
HoldTime,
HoldStep, FltType,
FltCutoff, FltReso,
FltEnvAtk,
FltEnvDecay,
FltEnvDepth,
FltVelo,
(FM) Morph,
FM Course
Selects the parameter that is modified by
the LFO.
LFO Depth
-128–0–+127
Specifies the amount that is modified by
the LFO.
* If the setting of the parameter to be
modified is 128 (the center value),
setting LFO Depth to +/-64 will cause the
parameter to vary in a range of 0–255.
Only for ACB tones of the BD category
Attack
0–255
Adjusts the attack strength of the bass
drum.
Only for ACB tones of the SD category
Snappy
0–255
Adjusts the volume of the snare wires
(resonating wires) of the snare drum.
Only for ACB tones of the TOM category
Color
-128–0–+127
(808 Low/Mid/High/Full Tom)
Adjusts the amount of ambience (amount
of noise).
(808 Noise Tom L/M/H)
Adjusts the amount of resonance.
(909 Low/Mid/High Tom)
Adjusts the amount of ambience (amount
of noise).
(707 Low/Mid/High/Full Tom)
Adjusts the amount by which the pitch
will change.
(606 Floor/Low/High/Full Tom)
Adjusts the amount of ambience (amount
of noise).
Sample tone only
Coarse Tune
-24–0–+24 Specifies the pitch in semitone steps.
Parameter Value Explanation
Rate
-1.00–0.00–+1.00
(steps of 0.01)
Specifies the playback direction and
playback speed.
+1.00: Play at the original speed.
+0.99–+0.01: Play at a lower speed.
0.00: Don’t play.
-0.01–-0.99: Play backward at a lower
speed.
-1.00: Play backward.
Spread
-50–0–+50
Slightly skews the pitch between left and
right, producing a stereo effect.
Bit Reduce
0–12 Adds a lo-fi effect.
Attack
0–255
Specifies the time over which the level
rises.
Hold Mode
Whole, Time,
Step
Selects how the sound decays.
Whole: The sound is heard to the end
without decaying.
Time: Decay begins after a specified
length of time.
Step: Decay begins after a specified
number of steps.
Hold Time
0–255
Specifies the time until decay begins when
Hold Mode = Time.
* The duration of the sound will be Attack
+ Hold Time + Decay.
Hold Step
0.5–128.0
(steps of 0.5)
Specifies the number of steps until decay
begins when Hold Mode = Step.
* The duration of the sound will be Hold
Step + Decay (Attack changes within
Hold Step).
Flt Type
LPF, HPF Selects the type of filter.
Flt Cutoff
0–255 Adjusts the cutoff frequency of the filter.
Flt Reso
0–255 Adjusts the amount of filter resonance.
Flt Attack
0–255
Specifies the attack time for the envelope
that varies the filter.
Flt Decay
0–255
Specifies the decay time for the envelope
that varies the filter.
Flt Env
0–255
Specifies the amount by which the
envelope varies the filter.
Flt Velo
0–255
Specifies the amount by which the note’s
velocity affects the filter.
FM tone only
Morph
-128–0–128 Adjusts the FM setting.
Only for FM tones of the FX/HIT–OTHERS categories
FM Coarse
-24–0–+24 Specifies the pitch in semitone steps.
MEMO
If the KIT: CTRL Sel parameter is set to “User,” editing the KIT CTRL:
BD–OH parameters lets you control them using the instrument edit
section’s [CTRL] knob (except for GAIN and LFO).