Roland TR-6S - Rear Panel Connections; Power Switch Operation; MIDI Connectors; USB Port Functionality

6
KIT Parameters
Parameter Value Explanation
Type
SBF1, SBF2, SBF3,
SBF4, SBF5, SBF6
Switches the range that can be adjusted
by BandIntrvl.
Switch the Type if you want to narrow
(or
widen)
the bands when adjusting BandIntrvl.
Gain
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the output gain.
NOISE
Color
MASTER FX [CTRL] *1
0–255
Moves a filter that is applied to noise.
If Color is set to 0, no noise is output.
This parameter is intended to be
controlled by the MASTER FX [CTRL] knob.
Level
MASTER FX [CTRL] *1
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the noise level.
Direction
UP, DOWN
Switches the direction in which the filter is
moved by Color.
*1 This can be controlled by specifying the Ctrl parameter.
KIT: EXT IN
Parameter Value Explanation
SideChnSrc
BD, SD, LT, HC,
CH, OH
Selects the instrument that is used as the
trigger for the side chain effect.
SideChnType
1–8
Selects the type of side chain effect.
1: Type = Ducking, Width = 1step
2: Type = Ducking, Width = 2step,
(Fast Rise)
3: Type = Ducking, Width = 1step,
(Slow Rise)
4: Type = Gate, Width = 1step
5: Type = Ducking, Width = Narrow
6: Type = Ducking, Width = 2step,
(Slow Rise)
7: Type = Gate, Width = Half step
8: Type = Ducking, Width = 1step,
(Unique Rise)
SideChnDpt
0–255 Adjusts the depth of the side chain effect.
Gain
-40.0dB–0.0dB–
+40.0dB
(0.5 dB increments)
Specifies the gain.
Pan
L127–CENTER–
R127
Specifies the stereo position.
ReverbSend
0–255 Adjusts the level sent to reverb.
DelaySend
0–255 Adjusts the level sent to delay.
KIT: LFO
Parameter Value Explanation
Waveform
SIN, TRI, SAW,
SQR, S&H
Selects the LFO waveform.
Tempo Sync
OFF, ON
Choose ON if you want the LFO to
synchronize with the tempo.
Rate
(TempoSync = OFF)
0–255
(TempoSync = ON)
64.00–0.25 step
(steps of 0.25)
Specifies the LFO rate.
KIT: MUTE
Parameter Value Explanation
BD,
SD,
LT,
HC,
CH,
OH
*2
OFF, BD, SD, LT,
HC, CH, OH
For the OpenHH sound and sample tones,
you can specify that their sound be muted
when another instrument is sounded.
* By selecting the instrument that plays
CloseHH, you can use CloseHH to close
(mute) the sustained sound of OpenHH.
KIT: CTRL
Parameter Value Explanation
Sel
[CTRL SELECT]
OFF, Pan,
ReverbSend,
DelaySend, LFO
Depth, InstFX,
User
Assigns a parameter to the [CTRL] knobs of
the instrument edit section so that it can
be controlled.
OFF: The [CTRL] knobs do nothing.
Pan: Control the pan of each instrument.
ReverbSend: Control the reverb send
level of each instrument.
DelaySend: Control the delay send level
of each instrument.
LFO Depth: Control the LFO effect depth
of each instrument.
InstFX: Control the INST FX effect that’s
selected for each instrument.
User: Control the parameter that’s
assigned for each instrument.
BD,
SD,
LT,
HC,
CH,
OH
*2
OFF, Pan,
ReverbSend,
DelaySend, LFO
Depth, InstFX,
(BD) Attack
(SD) Snappy
(FM) Morph
(FM) FM Coarse
(TOM) Color
(SAMPLE) Coarse,
Rate, Spread,
BitReduce,
Attack,
HoldMode,
HoldTime,
HoldStep,
FltType,
FltCutoff, FltReso,
FltEnvAtk,
FltEnvDecay,
FltEnvDepth,
FltVelo
This is shown only if you’ve set CTRL Sel
= User. It lets you assign a parameter for
each instrument to the [CTRL] knobs of
the instrument edit section.
KIT: COLOR
Parameter Value Explanation
BD,
SD,
LT,
HC,
CH,
OH
*2
RED, ORANGE,
YELLOW, LIME,
GREEN, SKYBLUE,
LIGHTBLUE,
BLUE, PURPLE,
MAGENTA, PINK,
WHITE
Specifies the color that each level fader
BD–RC will be when SLIDER LED Src is set
to kit.
When the cursor is located at color
(value) ,
you can also specify the color by moving
the slider.
*2 You can also use the instrument select [BD]–[RC] buttons to make a
selection.
KIT: NAME
Parameter Explanation
NAME
Specifies the name of the kit
(maximum 16 characters) .