5
KIT Parameters
Parameter Value Explanation
Balance
MASTER FX [CTRL] *1
OFF, 1–255
Adjusts the distortion effect.
With a setting of 255, the distortion effect
is at 100%.
Drive
MASTER FX [CTRL] *1
0–255
Adjusts the depth of distortion.
Because increasing Drive also increases
the output level, make adjustments by
lowering Level.
Tone
MASTER FX [CTRL] *1
0–255
Adjusts the tone.
Raising the Tone emphasizes the
highfrequency region.
Lowering the Tone emphasizes the low-
frequency region.
Level
MASTER FX [CTRL] *1
0–255
Specifies the output level.
Set this so that the volume is essentially
the same whether the MASTER FX Sw is
on or off.
FUZZ
Balance
MASTER FX [CTRL] *1
OFF, 1–255
Adjusts the fuzz effect.
With a setting of 255, the fuzz effect is at
100%.
Drive
MASTER FX [CTRL] *1
0–255
Adjusts the depth of distortion.
Because increasing Drive also increases
the output level, make adjustments by
lowering Level.
Tone
MASTER FX [CTRL] *1
0–255
Adjusts the tone.
Raising the Tone emphasizes the high-
frequency region.
Lowering the Tone emphasizes the low-
frequency region.
Level
MASTER FX [CTRL] *1
0–255
Specifies the output level.
Set this so that the volume is essentially
the same whether the MASTER FX Sw is
on or off.
CRUSHER
Balance
MASTER FX [CTRL] *1
OFF, 1–255
Adjusts the lo-fi effect.
With a setting of 255, the lo-fi effect is at
100%.
SampleRate
MASTER FX [CTRL] *1
0–255
Specifies the sampling frequency at which
the crusher effect resamples the sound.
Increasing the SampleRate lowers the
sampling frequency, producing a more
lo-fi sound.
Filter
MASTER FX [CTRL] *1
0–255
Specifies the cutoff frequency of the LPF
that is applied before Crusher resamples
the sound.
By lowering the Filter setting you can
reduce harsh high-frequency noise.
PHASER
Balance
MASTER FX [CTRL] *1
OFF, 1–255
Adjusts the phase effect.
With a setting of 255, the phase effect is
at 100%.
TempoSync
OFF, ON
Choose ON if you want the phase effect to
synchronize with the tempo.
Rate
MASTER FX [CTRL] *1
(TempoSync = OFF)
0–255
(TempoSync = ON)
64.00–0.25 step
(steps of 0.25)
Specifies the rate of the phase effect.
Depth
MASTER FX [CTRL] *1
0–255 Specifies the depth of the phase effect.
Resonance
MASTER FX [CTRL] *1
0–255
Adjusts the amount of resonance.
Raising the Resonance emphasizes the
effect and produces a strongly distinctive
sound.
Parameter Value Explanation
Manual
MASTER FX [CTRL] *1
0–255
Specifies the center frequency at which
the phase effect is applied.
By raising Manual, you can reduce the
phase effect in the low-frequency region.
(As necessary, lower Depth as well to lighten the phase effect)
Type
4ST, 8ST, 12ST,
BI-PHASE
Selects the structure of the phaser.
4ST: 4-stage phaser
(produces a light phase effect)
8ST: 8-stage phaser
(produces a typical phase effect)
12ST: 12-stage phase
(produces a deep phase effect)
BI-PHASE: a phaser that connects two
phase shift circuits in series
(produces a distinctive phase effect)
FLANGER
Balance
MASTER FX [CTRL] *1
OFF, 1–255
Adjusts the flanging effect.
With a setting of 255, the flanging effect
is at 100%.
TempoSync
OFF, ON
Choose ON if you want the flanging effect
to synchronize with the tempo.
Rate
MASTER FX [CTRL] *1
(TempoSync = OFF)
0–255
(TempoSync = ON)
64.00–0.25 step
(steps of 0.25)
Specifies the rate of the flanging effect.
Depth
MASTER FX [CTRL] *1
0–255 Specifies the depth of the flanging effect.
Resonance
MASTER FX [CTRL] *1
0–255
Adjusts the amount of resonance.
Raising the Resonance emphasizes the
effect and produces a strongly distinctive
sound.
Manual
MASTER FX [CTRL] *1
0–255
Specifies the center frequency at which
the flanging effect is applied.
By raising Manual, you can reduce the
flanging effect in the low-frequency
region.
(As necessary, you can also lower Depth to make the flanging
effect shallower.)
LoCutF
FLAT, 20Hz, 25Hz,
31.5Hz, 40Hz,
50Hz, 63Hz,
80Hz, 100Hz,
125Hz, 160Hz,
200Hz, 250Hz,
315Hz, 400Hz,
500Hz, 630Hz,
800Hz
Cuts the frequency region below the
specified frequency.
Mode
MONO, STEREO
Selects whether the flanging is modulated
in the same or the opposite way for left
and right.
MONO: Left and right are modulated in
the same way.
STEREO: Left and right are modulated in
the opposite way.
SBF
Balance
MASTER FX [CTRL] *1
OFF, 1–255
Adjusts the side band filter effect.
With a setting of 255, the side band filter
effect is at 100%.
BandIntrvl
MASTER FX [CTRL] *1
0–255
Adjusts the spacing of the bands.
As you raise BandIntrvl, the spacing
between the bands becomes wider, so
that only specific frequency regions are
passed.
Band Wifth
MASTER FX [CTRL] *1
0–255
Adjusts the width of the bands.
As you raise Band Width, the width of
each band becomes narrower, so that only
specific frequency regions are passed.
To Next Page
Loading...
