Roland TR-6S - KIT Parameters; KIT; KIT: REVERB; KIT: DELAY

2
KIT Parameters
KIT
Parameter Value Explanation
Level
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the volume of the kit.
KIT: REVERB
Parameter Value Explanation
Type
AMBI, ROOM,
HALL1, HALL2,
PLATE, MOD
Type of reverb
Time
[KIT] + [REVERB]
0–255 Specifies the reverb time.
Level
[REVERB]
OFF, 1–255 Specifies the volume of the reverb.
Pre Delay
0ms–100ms
Adjusts the time until the reverb sound
appears.
Low Cut
FLAT, 20Hz, 25Hz,
31.5Hz, 40Hz,
50Hz, 63Hz,
80Hz, 100Hz,
125Hz, 160Hz,
200Hz, 250Hz,
315Hz, 400Hz,
500Hz, 630Hz,
800Hz
Specifies the frequency below which the
low-frequency region of the reverb is cut.
HighCut
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz,
FLAT
Specifies the frequency above which the
high-frequency region of the reverb is cut.
Density
0–10 Density of reverb
KIT: DELAY
Parameter Value Explanation
Type
DELAY, PAN, TAPE
ECHO
Selects the type of delay.
TempoSync
OFF, ON
Choose ON if you want the delay time to
synchronize with the tempo.
Level
[DELAY]
OFF, 1–255 Specifies the volume of the delay.
Time
[KIT] + [DELAY]
(TempoSync = OFF)
0–255
(TempoSync = ON)
1/32, 1/16T,
1/32D, 1/16,
1/8T, 1/16D, 1/8,
1/4T, 1/8D, 1/4,
1/2T, 1/4D, 1/2,
1/1T, 1/2D, 1/1
Specifies the time by which the sound is
delayed.
Feedback
0–255
Adjusts the amount of feedback
(amount of
repetition)
.
Reverb Send
0–255 Specifies the send level to reverb.
Parameter Value Explanation
DLY, PAN
HighCut
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz,
FLAT
Specifies the frequency above which the
high-frequency region of the delay sound
is cut.
H Damp
0.0dB–-40.0dB
0.5 dB
increments), -INF
Adjusts the amount by which the high-
frequency region of the delay sound is cut
at each repetition.
H DampF
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz
Specifies the frequency above which H
Damp cuts the high-frequency region.
L Damp
0.0dB–-40.0dB
(0.5 dB increments) ,
-INF
Adjusts the amount by which the low-
frequency region of the delay sound is cut
at each repetition.
L DampF
80.0Hz, 100Hz,
125Hz, 160Hz,
200Hz, 250Hz,
315Hz, 400Hz,
500Hz, 630Hz,
800Hz
Specifies the frequency below which L
Damp cuts the low-frequency region.
PAN
Tap Time
0% –100%
Adjusts the delay
(tap) time of the right side,
relative to the left side as 100%.
TAPE ECHO
Mode
S, M, L, S+M, S+L,
M+L, S+M+L
Selects the combination of playback
heads.
S
(Short) , M (Middle) , L (Long)
Bass
-15dB–0dB–
+15dB
Adjusts the low-frequency region of the
echo sound.
Treble
-15dB–0dB–
+15dB
Adjusts the high-frequency region of the
echo sound.
Pan S
L127–CENTER–
R127
Specifies the panning of the S
(Short)
playback head.
Pan M
L127–CENTER–
R127
Specifies the panning of the M
(Middle)
playback head.
Pan L
L127–CENTER–
R127
Specifies the panning of the L
(Long)
playback head.
Tape Dist
0–8
Adjusts the amount of distortion for the
echo sound.
W/F Rate
0–255
Adjusts the modulation speed of wow and
flutter.
W/F Depth
0–255 Adjusts the depth of wow and flutter.