EasyManuals Logo

Rosenbauer R600 User Manual

Rosenbauer R600
70 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #52 background imageLoading...
Page #52 background image
Seite /
Page
- 52 -
28.03.1996 / PT / Rev 00
Feuerlöschpumpe R600
Fire Pump R600
© 1996
Prüf- und Kontrollarbeiten - Trockenvacuumprobe
Ein wichtiger Beitrag zur Wartung und Pflege der Pumpe, Schläu-
che und Kupplungen bildet die Überprüfung auf Dichtheit. Aus
diesem Grund sollte eine Trockenvakuumprobe nach jedem Betrieb
und in regelmäßigen Abständen - monatlich durchgeführt werden.
- Pumpe gründlich entleeren.
- Saugeingang mit Blinddeckel verschließen (wenn Saugschläuche
geprüft werden, diese ankuppeln und das Ende mit Blinddeckel
verschließen).
- Entleerungshahn und Druckventile schließen.
- Motor in Betrieb nehmen und entlüften. Wird die Pumpe allein
geprüft, so wird in wenigen Sekunden ein Unterdruck von ca.
0,8 bar erreicht.
- Pumpe ausschalten.
- Die Pumpe ist genügend dicht, wenn der Unterdruck innerhalb
1 Minute nicht weiter als von 0,8 auf 0,7 bar absinkt.
- Sollten 0,8 bar Unterdruck nicht erreicht werden, muß die
Pumpe abgedrückt werden. Dafür genügt ein Druck von 3 - 6
bar, angeschlossen am Saugeingang.
Wartung
Maintenance
Checking procedures - Dry vacuum test
An essential part of maintenance is to ensure that pump, hoses, and
couplings are water-tight. For this reason, dry vacuum tests should
be carried out after each use and and at regular intervals (monthly).
- Drain pump thoroughly.
- Close the suction inlet with a blind cap (when checking intake
hoses, couple them to suction inlet and close the end with a blind
cap).
- Close the drain valve and the pressure outlets.
- Engage the pump and prime.
When checking the pump only, a vacuum of 0.8 bar will be
obtained within a few seconds.
- Disengage pump and stop engine.
- Check the vacuum decrease with a timer. The pump is tight
enough (when checking pump only) if the vacuum does not
decrease from -0.8 to -0.7 bar within one minute.
- If -0.8 bar cannot be reached, the pump should be put under
pressure by water inducting. A pressure of 3 - 6 bar connected
to the suction inlet is sufficent.
+-
0
0
0
0
0
0
2
2
5
5
7
I
0
START
OFF
RUN
I
0
I+
I
0
I
0
I
0
0
I
0
I
0
3%
6%
8%
DIESEL
MOTOR
STOP
0
I
ND
AUSGANG
LINKS
ND
AUSGANG
RECHTS
+-
0
0
0
0
0
0
2
2
5
5
7
I
0
START
OFF
RUN
I
0
I+
I
0
I
0
I
0
0
I
0
I
0
3%
6%
8%
DIESEL
MOTOR
STOP
0
I
ND
AUSGANG
LINKS
ND
AUSGANG
RECHTS

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Rosenbauer R600 and is the answer not in the manual?

Rosenbauer R600 Specifications

General IconGeneral
BrandRosenbauer
ModelR600
CategoryWater Pump
LanguageEnglish

Related product manuals