Ross Ultricore RCP-ME - Page 94

Ross Ultricore RCP-ME

98 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

94 • DashBoard Interface Overview RCP-ME User Guide (v4.0)

Table of Contents

Default Chapter7
- Table of Contents7
Introduction11
- Related Publications11
- Documentation Conventions12
- Contacting Technical Support12
Hardware Overview15
- Front Panel Overview15
- Rear Panel Overview16
Getting Started17
- Features17
- Typical System Equipment17
- System Overview18
- How the RCP-ME and Routing Switchers Communicate18
- Installation and Configuration Overview19
- Physical Installation20
- Basic Configuration21
- Adding the RCP-ME to the Dashboard Tree View23
- Setting up the Routing Mode26
- Resetting Devices27
Destination and Sources29
- Specifying the Number of Outputs/Inputs29
- Assigning Output and Input Labels29
- Assigning a Destination or Source Button30
- Assigning a Crosspoint Button31
- Setting the Retry Time for a Switch Failure32
- Making a Switch32
- Toggling between Two Sources33
Breakaways and Levels35
- Setting up Breakaways35
- Automatically Resetting a Custom Breakaway to the Default Breakaway after a Switch36
- Assigning a Breakaway Button36
- Assigning a Breakaway Step Button37
- Router Levels37
- Assigning a Level Button38
- Selecting Breakaways and Levels38
- Viewing the Breakaways Assigned to an RCP-ME39
- Level Mask Mode39
Menus41
- Setting up Menus41
- Assigning a Menu Link Button42
- Assigning Menu Navigation Button42
- Returning to the Home Menu43
- Using a Menu43
Functions45
- What Is a Function45
- Assigning Functions to Buttons on the RCP-ME46
- Assigning a Protect Button47
- Assigning a Take Button47
- Assigning a Chop Button48
- Assigning a Shift Button48
- Assigning a Panel Lock Button49
- Clearing a Function from a Button50
Macros51
- What Is a Macro51
- Assigning a Macro Button51
- Recording a Macro Using the Panel51
- Editing a Macro Using the Panel52
- Configuring a Macro Using Dashboard52
- Using a Macro53
Salvos55
- What Is a Salvo55
- Assigning a Salvo to a Button55
- Using a Salvo55
Category Index Mode57
- Default Category Button Mapping57
- Entering Category Index Mode58
- Operating in Category Index Mode58
Protects and Locks61
- What Is a Protect61
- What Is a Lock61
- Assigning a Protect/Lock Button61
- Locking an RCP-ME62
- Protecting a Destination63
- Clearing Protects Held by an RCP-ME64
Machine Control65
- What Is Machine Control65
- Setting up Machine Control65
- Assigning a Machine Control Button65
- Configuring a De-Assign Button66
- De-Assigning a Machine Control Port66
Linking Remote Control Panels67
- Before You Begin67
- Configure a Link between Multiple Remote Control Panels67
- Operating Linked Remote Control Panels68
Cutbus Mode71
- Setting up Cutbus Normal Mode71
- Setting up Multi Cutbus Mode71
Managing Panel Configurations73
- Saving the Current Configuration for the RCP-ME73
- Editing a Configuration File74
- Sending a Configuration File to a Device74
- Loading the Factory Defaults Using Dashboard75
Monitoring77
- Adjusting the Contrast for the LCD77
- Viewing Status and Alarms in Dashboard77
- Troubleshooting78
- Loading the Factory Defaults Via Dashboard78
- Upgrading the Software78
Dashboard Interface Overview81
- RCP-ME Connection Editor Fields81
- Panel Config Interface83
RCP-ME Hexadecimal to Router Level Conversion95
Glossary97

Related product manuals

Preview: Ross NK Routing Systems RCP-QE

Ross NK Routing Systems RCP-QE