Rotel RCD-965BX - Advanced Troubleshooting and Specifications; Resolving Playback and Programming Issues

• There is an unwanted object in the disc tray, e.g. a
piece of paper or a remnant of packaging.
5. The disc is being played because the track number
or the time indication moves on regularly, but there is
no sound.
• The amplifier or the receiver is not switched on.
• The position of the amplifier source selector switch
dose not correspond with the input to which the player is
connected.
• The amplifier or the (active) loudspeakers connected
to it are not working. Check with another sound source to
see if this is the case.
• The microprocessor has not received the command
correctly. Check if switching the player off and on again,
and then re-starting clears the fault.
• The connection between the player and the amplifier
is broken.
• The input to which the player is connected is defec¬
tive. Check this by connecting the player to another input
socket.
6. The sound is poor or distorted or you can hear only
one channel.
• The player is not connected to the CD, AUX .TUNER
or TAPE IN input of the amplifier but to the PHONO input.
• One of the plugs of the connection cable is either not
connected or not properly connected.
• The disc is dirty or badly scratched. See if cleaning
the disc or using another clean or scratch-free disc im¬
proves the situation.
• There is an unwanted object in the disc tray, e.g. a
piece of paper or a remnant of packaging.
• The amplifier or the (active) loudspeakers connected
to it are not working properly. Check with another sound
source to see if this is the case.
7. Programming is not working.
• The disc is dirty or badly scratched. See if cleaning
the disc helps or try programming a scratch-free disc.
• The microprocessor has not processed the com¬
mands properly. Erase the program by pressing STOP and
store it again; re-start play and check if the fault has
cleared.
• All 20 memory places are already occupied and you
have missed the ERROR indicator that indicates this.
Check this by pressing PROGRAM and counting the num¬
ber of tracks displayed.
8. The following faults can be caused by the same
circumstances:
Playback does not begin with the first track number on the
disc or of the program, but with another. Playback stops
before the end of the disc or the program.
• The microprocessor has not processed the command
correctly. Check if switching the player off and on again,
and then re-starting clears the fault.
• The disc is dirty or badly scratched. See if cleaning
the disc or using another, clean or scratch-free, disc clears
the fault.
• The disc is defective. Try another disc and see if that
clears the fault. There is an unwanted object in the disc
tray, e.g. a piece of paper or a remnant of packaging.
SPECIFICATIONS RCD-965BX
AUDIO:
Number of Channels.2
Frequency Range.20 TO 20,000 Hz
Amplitude Linearity.+/- 0.05 dB
Channel Unbalance.+/- 0.5 dB
Phase Linearity.+/- 0.5 degrees
Signal-to-Noise Ratio.100 dB
Dymamic Range.96 dB
Channel Separation.100 dB (1 kHz)
THD + Noise.0.0025 % (1 kHz)
Intermodulation Distortion...0.0025 % (1 kHz)
Out-Band Rejection.>60 dB, above 24.1 kHz
Wow and Flutter.Quartz crystal precision
AUDIO LINE OUTPUT:
Max Output Level.2 V rms
Output Impedance.200 ohms
Min Load Impedance.10 kohms
DIGITAL OUTPUT:
Output Level.0.5 V P.P.
Load Impedance.75 ohms
MISCELLANEOUS:
Power Requirement.120 V/ 60 Hz, 220 V/ 50 Hz,
240 V/ 50 Hz (depending on
destinations)
Power Consumption.30 watts
Dimension (overall).440 (W) x 92 (H) x 316 (D) m^
17-3/8" x 3-5/8" x 12-7/16"
Weight (net).5.8 Kg /12.76 lbs
• Specifications and design subject to possible modifica¬
tion without notice.
7