Royal Sovereign RSC-6500H User Manual (English)

Other manuals for Royal Sovereign RSC-6500H

Questions and Answers:

B
brian19Jul 25, 2025
What to do if Royal Sovereign RSC-6500H Laminator rollers are not running?
- S
  Sally DiazJul 26, 2025
  If the rollers on your Royal Sovereign laminator aren't running, there could be several reasons: * Ensure the power plug is properly connected to a functioning outlet. * Disengage any emergency switches by rotating the knob clockwise. * If the film is jammed, try using the pressure lever and reverse button to un-jam it. * Confirm the front table switch is engaged. * Check the laser sensor to ensure it is in the correct position and free from obstructions. If these steps don't resolve the issue, it may be due to a defective main motor, main PCB, or motor controller. In this case, check if the connector of the wire-motor controller is connected correctly or consider replacing the motor controller.
M
molly68Jul 29, 2025
Why are the rollers not turning on my Royal Sovereign RSC-6500H Laminator after pressing the 'RUN' button?
- U
  urochaJul 30, 2025
  If your Royal Sovereign laminator has power but the rollers aren't turning after you press 'RUN', consider these possibilities: * Check if any emergency switches are engaged and disengage them. * Ensure the paper guide is correctly installed so that it activates the micro switch. * Inspect the motor fuse and replace it if it's blown.
S
Suzanne NguyenAug 3, 2025
Why is my Royal Sovereign RSC-6500H roller not heating?
- R
  Robin StricklandAug 3, 2025
  If the roller on your Royal Sovereign laminator is not heating, it could be due to several reasons: * Ensure the laminating mode is set to “Hot” and not “Cold”. Press the “HEAT” button on the control panel to change the mode. * Check the heating wire and connect it correctly. * A broken temperature bi-metal may be the cause, and it should be replaced. It is located on the right-hand side of the machine. * The temperature sensor may be defective and need replacement. It is set on the shaft behind the up roller. * The heater itself might be defective. Test its continuity with a multi-meter and replace it if it fails. * A defective main PCB could also be the cause, requiring replacement.
A
Austin KirkAug 7, 2025
What to do if the Royal Sovereign RSC-6500H machine will not turn on?
- S
  Shirley BlackburnAug 7, 2025
  If your Royal Sovereign laminator isn't turning on, check these potential causes: Ensure the power cord is properly plugged into the outlet. Verify that the power switch is in the “I” (On) position. Also, check if the circuit breaker has tripped and reset it if necessary. Finally, inspect the main power fuse and replace it if it's blown.
R
Robert KleinAug 11, 2025
What to do if Royal Sovereign RSC-6500H Laminator has no main power?
- J
  Julie ThompsonAug 11, 2025
  If your Royal Sovereign laminator has no main power, first double-check that your outlet has electricity. Also, ensure that the power source is suitable for the machine. If the issue persists, the main fuse may be defective and needs to be replaced.
A
Amanda WoodsAug 16, 2025
Why is Royal Sovereign RSC-6500H roller overheating?
- A
  Ann BrownAug 16, 2025
  If the roller on your Royal Sovereign laminator is overheating, it could be due to a defective temperature sensor, which would need to be replaced. Alternatively, a defective main PCB could be the cause, requiring replacement of the main PCB.
C
Cynthia DeckerAug 20, 2025
How to fix curled lamination on Royal Sovereign RSC-6500H Laminator?
- A
  Angela Clark DDSAug 20, 2025
  To fix curled lamination with your Royal Sovereign laminator: If the lamination is curling upward, loosen the top roll film tension. If the lamination is curling downward, loosen the bottom roll film tension.