- 8 -
Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values
SYSTEM STATUS REPORT CODES (✻59–✻68)
59
5959
59
EXIT
EXITEXIT
EXIT
ERROR
ERROR ERROR
ERROR
REP
REPREP
REP
Exit Error Report Code
[1]
60
6060
60
TROUBLE
TROUBLE TROUBLE
TROUBLE
REP
REP REP
REP
CODE
CODECODE
CODE
Trouble Report Code
|
[1,0]
61
6161
61
BYPASS
BYPASS BYPASS
BYPASS
REP
REP REP
REP
CODE
CODECODE
CODE
Bypass Report Code
|
[0,0]
62
6262
62
AC
ACAC
AC
LOSS
LOSS LOSS
LOSS
REP
REP REP
REP
CODE
CODE CODE
CODE
AC Loss Report Code
|
[0,0]
6
66
63
33
3
LOW
LOW LOW
LOW
BAT
BAT BAT
BAT
REP
REP REP
REP
CODE
CODECODE
CODE
Low Bat Report Code
|
[1,0]
6
66
64
44
4
TEST
TESTTEST
TEST
REP
REPREP
REPORT
ORTORT
ORT
CODE
CODE CODE
CODE
Test Report Code
|
[1,0]
65
6565
65
OPEN
OPEN OPEN
OPEN
REPORT
REPORT REPORT
REPORT
CODE
CODECODE
CODE
Open Report Code
†† [0]
66
6666
66
AWAY/STAY
AWAY/STAY AWAY/STAY
AWAY/STAY
REP
REPREP
REPORT
ORTORT
ORT
Arm Away/Stay Report Code
†† [0,0]
AWAY STAY
67
6767
67
RF
RF RF
RF
TRANS
TRANSTRANS
TRANS
LB
LB LB
LB
REP
REPREP
REP
RF Transmitter Low Battery Report Code
|
[1,0]
68
6868
68
CANCEL
CANCEL CANCEL
CANCEL
REP
REP REP
REP
CODE
CODECODE
CODE
Cancel Report Code
|
[1,0]
69
6969
69
RECENT CLOSE REP
RECENT CLOSE REPRECENT CLOSE REP
RECENT CLOSE REP
Recent Close Report Code
| [1]
Note: The control validates the data entered in this field. If the selection is not valid the control will
emit a single long beep indicating that the selection has been rejected. The control replaces
the selection with the default value “1”, which is displayed on the keypad, and advances to the
next field.
RESTORE REPORT CODES (✻70–✻76)
70
7070
70
ALARM
ALARM ALARM
ALARM
RES
RESRES
RES
REPORT
REPORT REPORT
REPORT
Alarm Restore Report Code
[1]
71
7171
71
TROUBLE RES REP
TROUBLE RES REPTROUBLE RES REP
TROUBLE RES REP
Trouble Restore Report Code
|
[1,0]
72
7272
72
BYPASS RES REP
BYPASS RES REPBYPASS RES REP
BYPASS RES REP
Bypass Restore Report Code
|
[0,0]
73
7373
73
AC R
AC RAC R
AC RESTORE REP
ESTORE REPESTORE REP
ESTORE REP
AC Restore Report Code
|
[0,0]
(†† 2nd digit is automatically sent as the user
number if expanded or 4+2 reporting is selected.)
2nd digit is automatically sent as 2nd digit of the zone alarm report
code programmed in
✻
56, if expanded or 4+2 reporting is
selected.
2nd digit is automatically sent as 2nd digit of the
zone alarm report code programmed in
✻
56, if
expanded or 4+2 reporting is selected.
To Next Page
Loading...