Salicru SLC CUBE 3+ User Manual

SLC CUBE 3+
USER'S MANUAL
UNINTERRUPTIBLE POWER SUPPLY

Salicru SLC CUBE 3+ Specifications

General

Brand	Salicru
Model	SLC CUBE 3+
Category	UPS
Language	English

Summary

2. INFORMATION FOR SAFETY.

4. PRESENTATION.

4.3. UPS FUNCTION STAGES.

4.4. OPERATING PRINCIPLE OF AN EQUIPMENT.

Explains how the UPS operates under various conditions.

4.5. OPERATING STRUCTURE OF A PARALLEL SYSTEM.

Describes how multiple UPS units operate together.

5. INSTALLATION.

5.1. RECEPTION OF THE EQUIPMENT.

5.2. CONNECTION.

Details the procedures for connecting power and communication cables.

5.1.4. Location, immobilised and considerations.

Covers site selection, leveling, and environmental considerations.

7. DESCRIPTION OF THE CONTROL PANEL.

7.1. CONTROL PANEL PARTS.

7.3. SCREEN DESCRIPTION.

7.3.2. "CONTROL AND STATUS OF THE EQUIPMENT" level See Fig 45.

7.3.3. "MEASUREMENT" level (screen menu 2.0). See fig. 46.

7.3.4. "PARAMETERS" level (screen menu 3.0). See fig 47.

7.3.5. "ALARMS" level (menu screen 4.0). See Fig 48.

Details the alarm conditions and messages displayed by the UPS.

7.2. BASIC FUNCTIONS OF THE SYNOPTIC KEYPAD.

7.3.1. Main level (screen menu 0.0). See Fig 44.

7.3.7. "CONFIGURATION" level (menu screen 6.0). See Fig 51.

7.3.8. Nominal values screens (menu screen 7.0). See Fig 50.

8. MAINTENANCE, WARRANTY AND SERVICE.

8.1. MAINTENANCE BASIC GUIDE.

4.3.8. Control panel.

4.3.9. Control software and communications.

4.3.9.1. Control software at low level.

4.3.9.2. Managing software of the equipment.

4.3.9.3. Communications.

Details the communication ports and protocols used by the UPS.

4.4. OPERATING PRINCIPLE OF AN EQUIPMENT.

4.4.1. Normal operating (⇨).

Describes the UPS operation during normal mains supply conditions.

4.4.2. Mains fault operating

Explains UPS operation during mains failure or blackout.

4.4.3. Operating with non-active inverter

4.4.4. Manual bypass operating

4.4.5. Smart ECO Mode operating

Details the energy-saving Smart ECO Mode operation.

4.4.6. Frequency converter operating.

4.5. OPERATING STRUCTURE OF A PARALLEL SYSTEM.

5.1.4. Location, immobilised and considerations.

5.1.4.1. Location for single equipments.

5.1.4.3. Equipment immobilized and levelled.

5.1.4.6. Access to inside the cabinet for its connection.

5.1.4.2. Location for parallel systems.

5.1.4.4. Preliminary considerations before connecting.

Lists essential checks and preparations before electrical connection.

5.1.4.5. Preliminary considerations before connecting, as regards to batteries and protections.

Covers safety and connection considerations for batteries and protection.

5.2. CONNECTION.

5.2.1. Connection to mains, terminals (X1 to X4).

Explains how to connect the main power supply to the UPS.

5.2.2. Connection of separate static bypass line, terminals (X14 a X17). CUBE3+ B version only.

Details connecting the separate static bypass line.

5.2.5. Connection to the input main protecting earth terminal (X5) and the earth bonding terminal (X10).

Explains how to connect the main earth ground and bonding terminals.

5.2.6. Relay COM port. Connector (X32).

5.2.7.2. COM or USB port. Connector (X31 USB).

5.2.10.1. Connection of the communication or BUS bundle (BC).

5.2.3. Connection to the output, terminals (X6 to X9).

Explains how to connect the output load to the UPS.

5.2.7. RS232/RS485 and USB COM 0 ports.

5.2.8. EPO terminals (X50).

5.2.4. Connection to the battery terminals of the equipment (X11, X12 and X23), with the battery modules (X47, X48 and X49).

Guides on connecting batteries to the UPS and battery modules.

5.2.10. Connection of parallel BUS (X36i) and (X360).

6. OPERATING.

6.1. RELEVANT PRELIMINARY CONSIDERATIONS.

6.5. COMPLETE SHUTDOWN OF THE UPS OR SYSTEM.

Provides the complete procedure for shutting down the UPS or system.

6.8. MANUAL BYPASS SWITCH (MAINTENANCE).

Details the manual bypass operation for maintenance.

6.8.3. Transference to normal operating, equipments with alphanumerical panel.

Details returning to normal operation for units with alphanumerical panels.

6.8.4. Transference to normal operating, for equipments with touch screen.

Guides returning to normal operation for units with touchscreen control.

6.2. UPS OR SYSTEM START UP.

Provides procedures for starting up the UPS or system.

6.6. EMERGENCY POWER OFF (EPO) BUTTON OPERATION.

6.7. SMART ECO MODE OPERATING.

6.2. UPS OR SYSTEM START UP.

6.2.1. Controls before starting up.

6.2.2.1. First start up procedure.

Guides through the initial setup and configuration upon first use.

6.2.2.4. Considerations regarding Master and Slave (parallel systems only).

6.2.2. Start up procedure.

Details the step-by-step process for starting up the UPS.

6.2.2.2. Daily start up procedure, for equipments with alphanumerical display.

Explains the daily startup process for units with alphanumerical displays.

6.2.2.3. Daily start up procedure, for equipments with touchscreen.

Explains the daily startup process for units with touchscreen control.

6.3. SHUTDOWN OF AN EQUIPMENT FROM PARALLEL SYSTEM.

6.4. TO START UP THE UPS OF PREVIOUS SECTION.