Samsung LN-T5265F - Anynet+ Receiver Audio and Service Points

English - 78
Setting Up Anynet
+
The following settings are to use Anynet
+
functions.
To use the Anynet+ Function, HDMI Control must be set to On
1. Press the Anynet
+
button.
3UHVVWKHŸRUźEXWWRQWRVHOHFW6HWXSWKHQSUHVVWKHENTER button.
2. Press the ENTER
button to select Anynet
+
(HDMI-CEC), then press the ENTER
button.
3,
3UHVVWKHŸRUźEXWWRQWRVHOHFW2QWKHQSUHVVWKHENTER button.
The Anynet+ (HDMI-CEC) function is enabled.
If you select Off, Anynet
+
(HDMI-CEC) is disabled.
Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off
2. 3UHVVWKHŸRUźEXWWRQWRVHOHFWAuto Turn Off, then press the ENTER button.
3. 3UHVVWKHŸRUźEXWWRQWRVHOHFW2QWKHQSUHVVWKHENTER
button.
The Auto turn off function is enabled.
If you select Off, the Auto turn off function is canceled.
Press the EXIT button to exit.
The Select Device setting of the TV remote control is to be set to TV to use the
Anynet
+
function.
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned off.
However, if the device is recording, it may not be turned off.
When the Anynet
+
(HDMI-CEC) function is disabled, all the Anynet
+
related operations are deactivated.
Scanning and Switching between Anynet+ Devices
1. Press the Anynet
+
button.
Anynet
+
devices connected with the TV are listed.
2.3UHVVWKHŸRUźEXWWRQWRVHOHFWWRDSDUWLFXODUGHYLFHDQGSUHVVWKHENTER button.
It is switched to the selected device.
3.,I\RXFDQQRWILQGDGHYLFH\RXZDQWSUHVVWKHŸRUźEXWWRQWRVHOHFW6HDUFKLQJ
Connections, then press the ENTER button.
The meassage Configuring Anynet+ connection... is displayed.
When searching devices completes, the connected devices are listed in the Anynet
+
menu.
Switching to the selected devices may take up to 2 minutes. You cannot cancel the
operation during the switching operation.
The time required to scan for devices is determined by the number of connected
devices.
When the device scan is complete, the number of found devices is not displayed.
Although the TV automatically scans devices when it is turned on using the POWER button, devices connected when the TV
is on or under a specific circumstance are not displayed in the device list. Therefore select Searching Connections menu to
search devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet
+
function. Make sure to
switch to an Anynet
+
device by using the Anynet
+
button.
Setup
HDMI Control
: Off
Auto Turn Off :Off
Searching Connections
Enter ReturnMove
Off
On
Enter
Move
Recevier: On
Connect Recorder
Setup
Air 28
Exit
Setup
HDMI Control
:On
Auto Turn Off :Off
Searching Connections
Enter ReturnMove
No
Yes
Enter Exit
Move
Recevier: On
Connect Recorder
Setup
Air 28
Setup
HDMI Control
2QŹ
Auto Turn Off :Yes Ź
Searching Connections Ź
Enter ReturnMove