What to do if I cannot connect to Samsung Security Camera using a tab browser of Internet Explorer 7.0?
To resolve the issue of not being able to connect to the Samsung Security Camera system using a tab browser of Internet Explorer 7.0, avoid using a new window or tab. Instead, select “File ? New session.” This is because an error may occur when connecting with a new window or tab since the cookie data are shared.
What to do if Samsung SNO-6011R Security Camera is not detected in the IP installer program?
If the Samsung Security Camera connected to the network is not detected by the IP installer program, try turning off the firewall settings on your PC and then search for the camera again.
Why does Samsung Security Camera viewer get disconnected during monitoring?
If your Samsung Security Camera viewer gets disconnected during monitoring, it might be due to changes in the camera or network configurations. Check all network connections to ensure stability. Also, if the camera is connected over a PPPoE network, poor network conditions could cause disconnections.
What to do if Samsung Security Camera cannot record into the Micro SD memory card?
If you cannot record into the Micro SD memory card with your Samsung Security Camera, check if the memory card is defective.
Why do Samsung SNO-6011R images overlap?
If images from your Samsung Security Camera overlap, it might be because two or more cameras are set to a single multicast address instead of different addresses. If a single address is used for multiple cameras, the images may overlap.
What to do if Samsung SNO-6011R does not operate properly with Micro SD memory card inserted?
If your Samsung Security Camera has a Micro SD memory card inserted but is not operating properly, first ensure the memory card is inserted in the correct direction. Also, if the memory card was formatted by other devices, it might not be compatible. You can format the memory card again in the camera's ? ? menu.
Why is Samsung SNO-6011R not sending notification e-mails when motion detection is enabled?
If the of is enabled on your Samsung Security Camera, but you are not receiving notification e-mails when an analysis event occurs, verify the following settings: First, check the settings. Second, ensure that is set to . Third, confirm that the option in the menu is checked.
General| Type | IP security camera |
|---|---|
| PTZ control | - |
| Placement supported | Indoor & outdoor |
| Connectivity technology | Wired |
| Wide Dynamic Range (WDR) | Yes |
| Form factor | Bullet |
| Product color | Gray |
| International Protection (IP) code | IP66 |
| Total megapixels | 2.38 MP |
| Maximum resolution | 1920 x 1080 pixels |
| Supported video modes | 1080p |
| Video formats supported | H.264, M-JPEG |
| Supported graphics resolutions | 320 x 180, 320 x 240, 1280 x 960, 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1600 x 1200 (UXGA), 1920 x 1080 (HD 1080), 640 x 480 (VGA), 800 x 600 (SVGA) |
| White balance | ATW, AWC, Indoor, Manual, Outdoor |
| Camera shutter type | Electronic |
| Camera shutter speed | 1/30 - 1/12000 s |
| Minimum illumination | 0 lx |
| Sensor type | CMOS |
| Optical sensor size | 1/2.8 \ |
| Optical zoom | 0 x |
| Zoom capability | No |
| Fixed focal length | 3.8 mm |
| Compatible memory cards | MicroSD (TransFlash), MicroSDHC, MicroSDXC |
| LED type | IR |
| Night vision distance | 15 m |
| Number of illumination LEDs | 30 |
| Cabling technology | 10/100Base-T(X) |
| Supported network protocols | IPv4, IPv6, TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS, SSL, DHCP, PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS, QoS, PIM-SM, UPnP, Bonjour |
| Compliance industry standards | IEEE 802.3af |
| Ethernet LAN (RJ-45) ports | 1 |
| Signal-to-Noise Ratio (SNR) | 50 dB |
| Power source type | PoE |
| Power consumption (max) | 7.7 W |
| Storage temperature (T-T) | -30 - 60 °C |
| Operating temperature (T-T) | -30 - 55 °C |
| Operating relative humidity (H-H) | 0 - 90 % |
| Mac operating systems supported | Mac OS X 10.7 Lion, Mac OS X 10.8 Mountain Lion, Mac OS X 10.9 Mavericks |
| Windows operating systems supported | Windows 7 Enterprise, Windows 7 Enterprise x64, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows 8.1, Windows 8.1 Enterprise, Windows 8.1 Enterprise x64, Windows 8.1 Pro, Windows 8.1 Pro x64, Windows 8.1 x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64 |
Weight and Dimensions| Depth | 302.4 mm |
|---|---|
| Width | 77.1 mm |
| Height | 83 mm |
| Weight | 560 g |
Read and follow all safety precautions to prevent hazards.
Details on dustproof/waterproof design, IR mode, visibility, video quality, and more.
Minimum hardware and software requirements for PC compatibility.
Guidelines for selecting compatible and high-performance memory cards.
List of items included in the product package for setup and use.
Visual identification and description of the SND-6011R camera's external parts.
Detailed identification and function of each numbered component of the SND-6011R.
Visual identification and description of the SNO-6011R camera's external parts.
Detailed identification and function of each numbered component of the SNO-6011R.
Essential safety guidelines and considerations before installing the camera.
Step-by-step guide for disassembling and installing the SND-6011R camera.
Step-by-step guide for installing the SNO-6011R camera.
Instructions for waterproofing connections when installing the camera outdoors.
How to pan, tilt, and rotate the camera for optimal monitoring angles.
Procedure for installing and ejecting the Micro SD memory card.
Details on memory card compatibility, speed, and usage for recording.
Diagrams showing how to connect the camera to monitors and PoE devices.
Guidelines for connecting the camera using an Ethernet cable.
How to connect alarm input sensors to the camera's port box.
Wiring diagram and instructions for connecting external alarm sensors.
Accessing the camera from a local PC within the LAN.
Network setup for connecting the camera to a DHCP modem.
Network setup for connecting the camera to a PPPoE modem.
Configuring PC network settings for router connection.
Explanation of the functions of buttons within the IP Installer tool.
Manual configuration of IP address, subnet mask, and gateway.
Checking and configuring dynamic IP addresses for network connection.
Setting up port forwarding on the router for remote access.
Accessing the camera via IP Installer from a shared PC on the local network.
Accessing the camera remotely using the camera's DDNS URL.
Steps to access the camera's web interface using its IP address.
Accessing the camera remotely via its DDNS URL.
Automatic camera discovery and connection using UPnP protocol.
Automatic camera discovery and connection using Bonjour protocol.
Entering username and password to access the camera's web viewer.
Guide for installing the necessary Microsoft Silverlight software.
Steps to install the WebViewer plugin for real-time camera access.
Navigating and utilizing features on the live video screen interface.
How to search and play back recorded video from the Micro SD card.
Steps to play recorded video based on specific event search criteria.
Steps to play recorded video by selecting a specific date and time.
Procedure for saving searched video content to a file.
Configure video settings like profile, source, and privacy zones.
Adjust sensor, SSDR, white balance, exposure, day/night, and special settings.
Configure IP type, MAC address, IP address, subnet mask, gateway, and DNS.
Set up Dynamic Domain Name Service for easy access.
Create lists to grant or deny access based on IP addresses.
Select secure connection system or install public certificate.
Configure 802.1x protocol and install certification.
Specify priority for stable transfer rate for specific IPs.
Configure SNMP protocols for network device monitoring.
Enable automatic camera search via UPnP protocol.
Enable automatic camera search via Bonjour protocol.
Configure FTP/Email, storage, alarm input, time schedule, and detection settings.
Configure server settings for transferring images during events.
Set recording conditions, check data size, or format Micro SD memory.
Set alarm input type, activation time, and operation mode.
Set video data saving interval as scheduled.
Configure detection of tampering attempts and trigger events.
Set up motion detection and video analysis for event triggering.
Set up face detection and trigger events accordingly.
Save events of a physically disconnected network.
Configure product information, date/time, user, and system upgrade/reboot.
View or provide camera model, serial number, and location details.
Specify time and date applied to the camera, including timezone.
Manage administrator password, guest access, and user permissions.
Perform system upgrade, factory reset, or restart the device.
Detailed technical specifications for the camera models.
Dimensional drawings and measurements of the camera models.
Solutions to common problems encountered while using the camera.
List of open-source software components and their licenses used in the product.
To Next Page