Why is my Samsung SPU-3750T picture flickering?
If the picture from your Samsung Security Camera is flickering, check the dome cover or lens for dirt or smudges and clean them. Also, check if the camera is pointed directly at a fluorescent light or sunlight; if so, change the camera's direction to eliminate the flickering.
Why is there no picture displayed on my Samsung SPU-3750T?
If no picture is displayed on the monitor, verify that the power cable is securely connected to both the camera and the monitor, and that the video cable is properly connected. Also, check if the iris of the lens is closed and adjust the iris settings if needed. Additionally, examine the camera's fixed shutter speed and adjust the shutter menu.
Why is the screen black on my Samsung SPU-3750T?
If you can’t see the screen and it appears black on your Samsung Security Camera, it may be due to the camera’s internal temperature dropping to -20 or lower, which can prevent video signal transmission. This does not indicate breakage; the camera will reset itself and display video again once its internal temperature reaches -20 or higher.
What to do if my Samsung Security Camera picture is out of focus?
If the picture from your Samsung Security Camera is out of focus: * Check if the dome cover or camera lens is dirty; if so, clean it. * Verify the distance between the camera, the subject, and the surroundings, noting that the camera might struggle to focus on a subject against a white background. * If auto-focus is failing, switch to manual focus and adjust it yourself. * Restore the camera settings to default using the reset menu. * Adjust the sharpness level.
How to fix a Samsung SPU-3750T picture that is too dark or bright?
If the picture from your Samsung Security Camera is too dark or too bright, you should check the camera's Brightness menu and adjust the brightness settings accordingly.
How to clear the 'Fan life Expired' message on my Samsung Security Camera?
To remove the message “ Fan life Expired. Replace the Fans” from the screen of your Samsung Security Camera, please make sure to "Clear" the message from the screen.
Why didn't my Samsung SPU-3750T Security Camera start running after turning on the power?
If your Samsung Security Camera didn't start running after turning on the power, check the environment temperature; the camera may not operate properly if it has been left at temperatures lower than -50 for a prolonged duration. The motor may malfunction at temperatures lower than -20; please turn on the camera in Standby mode instead of [Initialize]. Keep in Standby mode for at least 90 minutes. Once the internal temperature reaches -20 or higher, the camera automatically resets itself and activates the [Initialize] mode for normal operation.
Why can’t I activate the Sequence command on my Samsung SPU-3750T?
If you can use the controller but can’t activate the Sequence command on your Samsung Security Camera, it may be because the camera's internal temperature is between -10 to -20, which can cause the motor to malfunction and limit the use of the Sequence and Turbo commands. Once the internal temperature reaches -10 or higher, all Sequence modes become reactivated normally.
Why does my Samsung SPU-3750T Security Camera switch between color and B&W frequently?
If your Samsung Security Camera switches between color and B&W modes frequently, adjust the Duration and Dwell Time in the Day & Night menu.
Why does my Samsung SPU-3750T monitor display a white image?
If the monitor displays a white image when using your Samsung Security Camera, check if the iris of the lens is open and adjust the menu for the iris of the lens.
General| Effective Pixels | 768(H) x 494(V) |
|---|---|
| Lens | 3.6x V/F (f=3.8 ~ 10mm) |
| Power Consumption | Max. 12W |
| Power Supply | DC 12V ±10% |
| Image Sensor | 1/3" CCD |
| Back Light Compensation | Yes |
| Digital Noise Reduction | Yes |
| Privacy Masking | Off / On |
| White Balance | Auto / Manual |
| Operating Temperature | -10°C ~ +50°C (+14°F ~ +122°F) |
| Type | Dome Camera |
| Sensor | 1/3" Interline Transfer CCD |
| Signal to Noise Ratio | 50dB |
| Video Output | 1.0 Vp-p Composite (75Ω/BNC) |
To Next Page
