How to connect to Samsung IP Camera with Internet Explorer 7.0?
When connecting to a Samsung IP Camera with Internet Explorer 7.0, an error may occur when using a new window or tab due to shared cookie data. To avoid this, do not use a new window or tab; instead, select 'File ? New session'.
Why is my Samsung Security Camera not detected in the IP installer program?
If your Samsung Security Camera isn't being detected by the IP installer program, try turning off the firewall settings on your PC and then search for the camera again.
Why is there no image appearing on my Samsung SNB-6004?
If no image appears, and the transmission method is set to multicast, verify that the LAN the camera is connected to has a router that supports multicast.
What to do if I cannot record into the Micro SD memory card of my Samsung SNB-6004?
If you cannot record onto the Micro SD memory card, check to see if the memory card is defective.
What to do if the Samsung SNB-6004 Security Camera viewer got disconnected during monitoring?
If the viewer disconnects during monitoring, it may be due to changes in camera or network configurations. Check all network connections. Also, if the camera is connected over a PPPoE network, poor network conditions might cause disconnections.
What to do if my Samsung IP Camera does not operate properly with Micro SD memory card?
If your Samsung IP Camera does not operate properly with a Micro SD memory card inserted: * Check if the memory card is inserted in the proper direction. * If the memory card was formatted by other devices, it might not be compatible. Format the memory card again in the camera's Setup ? Event ? Storage menu.
What to do if my Samsung IP Camera cannot record into the Micro SD memory card?
If your Samsung IP Camera cannot record into the Micro SD memory card, check if the memory card is defective.
Why am I not receiving notification emails from my Samsung IP Camera?
If you are not receiving notification emails from your Samsung IP Camera even when motion detection or video analytics are enabled, verify the following settings in sequence: A. Check the Data & Time settings. B. Ensure the Motion detection / Video analytics is enabled. C. Check if the E-mail option of the Event action setup menu is checked for use.
What to do if my Samsung IP Camera viewer got disconnected during monitoring?
If your Samsung IP Camera viewer disconnects during monitoring, this can happen due to a few reasons: * If any changes are made to the camera or network configurations, connected viewers will be disconnected. Check all network connections. * If the connection is over a PPPoE network, poor network conditions can cause disconnections.
What to do if no signal is found at the Alarm Output port of my Samsung SNB-6004?
If there is no signal at the Alarm Output port when an intelligent video analysis event occurs, check the alarm output port settings.
General| Brand | Samsung |
|---|---|
| Model | SNB-6004 |
| Category | Security Camera |
| Language | English |
Essential safety guidelines for operating the apparatus to prevent hazards.
Steps to connect the camera directly to a local network via a PC.
Connecting the camera to a DSL/Cable modem using DHCP for internet access.
Steps for connecting the camera to a PPPoE modem with service ID and password.
Connecting the camera to a broadband router for home or small office networks.
Manual configuration of IP address, subnet mask, and gateway.
Automated network configuration using IP Installer for camera setup.
Configuration for dynamic IP environments, including DHCP server usage.
Configuring the broadband router to allow remote access to the camera.
Instructions for accessing the camera through a web browser using IP address.
Procedure for entering user ID and password to access the camera.
Procedure for installing the necessary plugin for real-time camera control.
Overview of the live video display interface and its controls.
How to search and play back recorded video data from storage.
Configuration options for video and audio settings, including profiles.
Setting video profile properties, connection policies, and individual properties.
Steps to add, modify, and configure video profiles with various parameters.
Adjusting video source, flip/mirror modes, analog output, and video type.
Defining specific areas within the video to be protected for privacy.
Configuring audio input sources, codecs, bitrate, gain, and output levels.
Adjusting image presets, sensor, SSDR, white balance, backlight, exposure, etc.
Creating and scheduling custom image presets for specific viewing conditions.
Adjusting brightness, shutter speed, anti-flicker, SSNR, lens, and AGC.
Adjusting brightness, shutter, SSNR, iris, and AGC for the SND-6083 camera.
Adjusting brightness, shutter, SSNR, iris, and AGC for the SND-6084 camera.
Configuring network interface settings, IP types, and IPv6.
Setting IP connection type (Manual, DHCP, PPPoE) and IPv6 options.
Configuring HTTP, HTTPS, RTSP, and other ports for camera access.
Configuring Dynamic Domain Name Service for remote access.
Configuring FTP/Email server settings for event image transfer.
Setting up FTP and Email servers for event notifications.
Activating recording, setting conditions, and managing data capacity.
Configuring storage actions, record profiles, and file formats for SD card recording.
Setting up NAS connection and saving operations for network storage.
Configuring alarm input types, activation times, and operation modes.
Configuring sensitivity and activation conditions to detect tampering attempts.
Setting up events for motion detection and intelligent video analysis.
Configuring sensitivity, size, and area for detecting motion.
Setting up video analysis types, rules, and detection overlays.
Configuring sensitivity, area, and activation for detecting faces.
Setting sound level, activation time, and conditions for detecting audio events.
Configuring alarm output types, modes, and duration for triggered events.
Managing product information, date, time, user accounts, and upgrades.
Managing administrator and guest accounts, and user permissions.
Performing system upgrades, factory resets, backups, and reboots.
Solutions for common problems encountered with camera operation and connectivity.
To Next Page
