Need help?Do you have a question about the Sartorius CPA124S and is the answer not in the manual?
General| Maximum Capacity | 120 g |
|---|---|
| Readability | 0.1 mg |
| Display | LCD |
| Repeatability (Standard Deviation) | 0.1 mg |
| Linearity | ± 0.2 mg |
| Interface | RS232 |
Guidelines for handling the balance during storage and transit to prevent damage.
Instructions for checking the balance for any external damage immediately after unpacking.
Procedures for allowing the balance to acclimate to room temperature after transfer to a warmer area.
Information about the control seal on verified balances for legal metrology applications.
Step-by-step guide for installing CPA2P balance components inside the chamber.
Guide for installing CPA2P-F components for weighing filters or standard pans.
Instructions for positioning and securing balances with an analytical draft shield.
Steps for placing components inside the chamber for triangular weighing pans.
Steps for placing components inside the chamber for round weighing pans.
Procedure for connecting the CPA26P/CPA225D models to their electronics box.
Instructions for placing and securing the draft shield on balances with a 3-sided design.
Steps for placing components for rectangular pans with capacities up to 10 kg.
Steps for placing the weighing pan on balances with rectangular pans over 10 kg.
Detailed steps for connecting the balance to AC power, including adapter usage.
Information on selecting and connecting country-specific power cords for the AC adapter.
Procedure for connecting the AC adapter for balances with weighing capacities exceeding 10 kg.
Safety precautions for plug-in AC adapters and FCC compliance information.
Details on FCC statements for Class A/B devices and interference mitigation.
Detailed explanation of the balance display and all operating elements and their functions.
Description of numbered display elements and their corresponding functions, including keys.
Guidance on working with microbalances, emphasizing steady hands and test measurements.
Explanation of the symbol indicating power disconnection and the balance self-test.
How to tare the balance and the meaning of the symbol indicating processor activity.
Procedure for switching off the balance and the meaning of the stand-by mode symbol.
Instructions for setting up filter weighing with the CPA2P-F model using a filter pan.
Location of the port for below-balance weighing hangers and its restrictions in legal metrology.
Steps for setting up below-balance weighing on CPA2P microbalances, including removing screws and attaching hooks.
Information on external calibration requirements for verified balances of accuracy class II.
Steps for performing internal calibration using the motorized weight and adjusting the balance.
How to configure the sequence of calibration and automatic adjustment via menu codes.
Explanation of the isoCAL feature, its activation conditions, and display prompts.
Permitted operating temperature ranges for isoCAL when balances are used in legal metrology.
Detailed step-by-step guide for performing internal calibration and adjustment on the balance.
Detailed step-by-step guide for performing external calibration and adjustment using a calibration weight.
How to print current parameter settings from different menu levels.
Example of setting parameters to adapt the balance to 'very unstable' ambient conditions using menu codes.
Overview of parameter settings related to weighing, including filter, stability range, and tare function.
Settings for display accuracy, CAL key function, and calibration/adjustment sequence modes.
Settings for weight units, display accuracy, decimal places, and animal weighing parameters.
Configuration options for data interface, including baud rate, parity, stop bits, and handshake mode.
Settings for printing application parameters, line format, and ISO/GLP compliant printouts.
How to set IDs, time, date, and display brightness for ISO/GLP records and ambient lighting.
A step-by-step example demonstrating how to set the time, date, and adjust display brightness.
Final steps for setting display brightness and saving or exiting the configuration menu.
Explanation of function keys (F, CF) used for starting, toggling, and ending application programs.
Symbols used to indicate calculated values like percent, piece count, and computed value.
Explanation of the Net-total Formulation program for weighing components up to a defined total.
Steps to set parameters for automatic printout when components are stored in the Net-total program.
Examples of data output formats for the Net-total Formulation program.
A step-by-step example demonstrating how to count parts using the Net-total formulation application.
Final steps of the counting example, including displaying total weight and storing component data.
Explanation of the Counting program for determining the number of parts based on a reference weight.
How automatic reference sample updating optimizes counting accuracy and can be activated/deactivated.
Benefits and setup for using a reference balance/scale for higher precision in counting large quantities.
Setting parameters for the Counting program, including storage resolution and reference updating.
Format of the printout for the Counting application, showing reference quantity and calculated quantity.
A step-by-step example of counting parts of equal weight using the balance.
Explanation of the Weighing in Percent program for obtaining weight readouts proportional to a reference weight.
Setting parameters for the Weighing in Percent program, including storage and decimal places.
Example of the printout format for the Weighing in Percent application.
A step-by-step example of determining residual weight in percent using the balance.
Explanation of the Animal Weighing program for determining weights of unstable samples by averaging.
Setting parameters for the Animal Weighing program, including animal activity and start mode.
Format of the printout for the Animal Weighing application, showing subweighing operations and calculated average.
A step-by-step example of determining animal weight using automatic start with a set number of subweighing operations.
How to configure the 'Toggle Weight Units' application to switch between two weight units.
Settings for printing initialization values for active application programs.
Options for generating ISO/GLP-compliant printouts that include ambient characteristics.
Settings for automatic weight value printouts, including conditions and interruption.
Examples of printouts showing weight or calculated values without data ID codes.
Examples of printouts that include data ID codes for identification.
Examples of generating printouts of configured initialization values for applications.
Examples of automatically printed weight readouts, showing different status indicators.
Parameters included in ISO/GLP printouts, such as date, time, manufacturer, model, and serial number.
Menu codes for configuring ISO/GLP compliant records, including calibration/adjustment or always on.
Examples of lines found in ISO/GLP compliant printouts, including measurement series and counting results.
Examples of ISO/GLP printouts specifically for external calibration and adjustment procedures.
Default factory settings for interface parameters like transmission rate, parity, and handshake.
How non-verified digits are identified on printouts using specific menu settings.
Characters output during normal operation in a 16-character format, including digits, units, and control codes.
Special codes used in the 16-character output format, such as overload/underload indicators.
Error codes and their representation in the 16-character output format.
Structure of the 22-character output format, including ID codes and subsequent data.
Meanings of various ID codes used in data output, such as Net-total, Counting, and Weighing in percent.
Formats for control commands sent to the balance, including escape sequences and command characters.
Requirements for error-free data communication, matching parameters between balance and connected device.
Explanation of hardware and software handshake options for balance interface communication.
Control of software handshake using XON/XOFF signals for device communication.
Settings for automatic data output without a print command, based on print intervals and stability.
Detailed pin assignments for the interface connector, including signal ground, data output, and power.
Critical warning about potential incorrect pin assignments in third-party RS-232 cables and damage risk.
Diagram illustrating the cabling for connecting a computer to the balance using RS-232C/V24 protocol.
Table listing display errors, their causes, and corresponding solutions for common issues.
Steps for preparing CPA2P models for transport, including removing parts and securing doors.
Steps for preparing CPA2P-F models for transport, including filter pan and draft shield removal.
Information on service contracts offered by Sartorius.
Guidelines regarding professional repair work performed by trained technicians.
General procedures for cleaning the balance, including unplugging power and using mild detergent.
Specific instructions for cleaning stainless steel parts, including the weighing pan.
Instructions for cleaning the weighing chamber and draft shield, including removal of parts and sample material.
Procedures to follow if safe operation is no longer warranted, including power disconnection and contacting service.
Information on proper disposal of packaging, equipment, and batteries according to EU legislation.
Technical specifications for the CPA2P model, including weighing range, readability, and dimensions.
Technical specifications for the CPA2P-F model, including weighing range, readability, and dimensions.
Technical specifications for CPA26P and CPA225D models, covering capacity, readability, and operating conditions.
Technical specifications for CPA324S, CPA224S, and CPA124S models, including pan size and interface details.
Technical specifications for CPA64 and CPA64-WDS models, including dimensions and weight units.
Technical specifications for the GCA1603P model, detailing capacity, operating temperature, and interface.
Technical specifications for the GCA803S model, detailing capacity, operating temperature, and interface.
Technical specifications for the GCA2502 model, detailing capacity, operating temperature, and interface.
Technical specifications for CPA1003S and CPA1003P models, including capacity, readability, and dimensions.
Technical specifications for the CPA623S model, including capacity, readability, and dimensions.
Technical specifications for CPA423S, CPA323S, and CPA223S models, including capacity, readability, and dimensions.
Technical specifications for CPA6202S and CPA6202P models, including capacity, readability, and dimensions.
Technical specifications for GPA5202, CPA4202S, CPA3202S, and CPA2202S models.
Technical specifications for the CPA10001 model, including capacity, readability, and dimensions.
Technical specifications for the CPA8201 model, including capacity, readability, and dimensions.
Technical specifications for the CPA5201 model, including capacity, readability, and dimensions.
Technical specifications for CPA34001S and CPA34001P models.
Technical specifications for the CPA16001S model.
Technical specifications for the CPA12001S model.
Technical specifications for the CPA34000 model.
Technical specifications for CPA26P and CPA225D models, including accuracy class and operating temperature.
Technical specifications for CPA324S and CPA224S models, including accuracy class and operating temperature.
Technical specifications for the CPA124S model, including accuracy class and operating temperature.
Technical specifications for the CPA64 model, including accuracy class and operating temperature.
Technical specifications for CPA1003S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA623S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA523S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA423S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA323S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA223S model, including capacity, accuracy class, and operating temperature.
Technical specifications for GC1603S model, including capacity, accuracy class, and operating temperature.
Technical specifications for GC803S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA6202S and CPA6202P models, including capacity, accuracy class, and operating temperature.
Technical specifications for GPA5202, CPA4202S, CPA3202S, and CPA2202S models.
Technical specifications for CPA10001 model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA8201 model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA5201 model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA2201 model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA34001S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA34001P model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA16001S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA12001S model, including capacity, accuracy class, and operating temperature.
Technical specifications for CPA34000 model, including capacity, accuracy class, and operating temperature.
Description and order number for the Sartorius data printer accessory.
Description and order number for the reflective remote display accessory.
Description and order numbers for rechargeable battery packs for different weighing capacities.
Description and order numbers for carrying cases for analytical draft shield chambers or standard models.
Software for transferring weighing data to a computer, with associated adapter cables and order numbers.
Description and order number for the density determination kit accessory.
Description and order number for the antistatic weighing pan accessory.
Information on calibration weights available for CPA balances, including DKD certificate option.
Guide for optimum use of the balance in quality management systems.
Models ING1 and ING2 industrial AC adapters for balances, with specifications and order numbers.
Description and order number for the analytical draft shield chamber accessory.
Description and order number for a draft shield cover with a 30mm opening.
Order numbers for data cables for PC connection (25-pin and 9-pin).
Description and order number for a D-Sub adapter cable.
Description of universal remote control switches (foot/hand) for balance functions.
Note regarding the T-connector's limited use with multiple intelligent peripherals.
Order number for the below-balance weighing hanger accessory.
Order numbers for weighing bowls of different volumes.
Order numbers for dust covers for various balance models.
Information on Council Directive 90/384/EEC regulating non-automatic weighing instruments for legal metrology.
Information regarding EC Type-Approval Certificates for verified weighing instruments.
Regulation of EC verification by manufacturers with Type-Approval Certificates.
Sartorius AG's compliance with EC Directive 90/384/EEC and its accreditation.
Services provided for initial verification and optimal operation of weighing instruments.
Sartorius service technicians authorized for legal metrological verification and inspection.
Information on the validity of verification and national regulations in European countries.
Details about the apparatus (Electronic precision weighing instrument) and its type designation.
Statement of compliance with Electromagnetic compatibility and Low Voltage Directives.
List of weighing instrument types, their accuracy classes, and EC Type-Approval certificate numbers.
Declaration by SARTORIUS AG regarding compliance with weighing instrument directives and standards.
Details on the issuing authority, legal basis, and type of apparatus covered by the certificate.
Illustrations and explanations of plates and markings on BC BL 100, BD BL 100, and BD BL 200 models.
Illustrations and explanations of plates and markings on the BF BL 500 model.
Legend defining the meaning of symbols (K, M, S, MD, T) used on the plates and markings.
An example of a plate showing the model designation (T).
An example of a descriptive plate (K) on a verified instrument, showing CE mark and metrology sticker.
To Next Page
