Application: Net-total Formulation R
With the Net-total Formulation
application, you can weigh in different
components up to a defined total.
Each component is saved in a net-total
memory.
Features
– Weigh in up to 999 components
in series
– Net-total formulation cannot be
combined with other applications
– Current component number displayed
in the text line (indicating the compo-
nent to be added)
– Toggle the display between “compo-
nent mode" and “additive mode"
by pressing w.
– Component mode: Display the
weight of the component currently
on the platform (for 1 second after it
is saved; then the platform is tared)
– Additive mode: Display the weight
of all components on the platform
(after it is saved, the net weight
of the last component added is
displayed briefly)
– Activate info-mode by pressing I
– Automatic printout each of component
as it is saved. Configuration:
appl R: 3.17.
If menu item 3.17.2 is set, the entire
component printout is generated every
time a component is saved. If menu
item
3.17.3 is set, the full printout
is generated only once, for the first
component:
Blank line, date, time, ID1 through ID4,
header lines 1 and 2. For subsequent
components, each “component" item
(“Comp xx") is followed by a blank line.
– Automatic taring of container weight.
Configuration:
appl R: 3.7.
– Restore factory default settings.
Configuration:
appl R: 9.1.
Preparation
§ Switch on the scale: Press e
§ While all segments are lit,
press the ) key
§ Select the Application menu: Press k
repeatedly until
APPL is displayed
§ Open the Application menu:
Press the ) key
§ Select the Net-total Formulation
application:
Press the k key repeatedly until
the desired menu item is displayed and
press ) to open the submenu
Application Parameters:
Net-Total Formulation
3.5. Minimum load for automatic
taring and automatic printing
3.5.1* 1 digit
3.5.2 2 digits
3.5.3 5 digits
3.5.4 10 digits
3.5.5 20 digits
3.5.6 50 digits
3.5.7 100 digits
3.5.8 200 digits
3.5.9 500 digits
3.5.10 1000 digits
3.6. Minimum load for automatically
saving/transferring values
3.6.1* 1 digit
3.6.2 2 digits
3.6.3 5 digits
3.6.4 10 digits
3.6.5 20 digits
3.6.6 50 digits
3.6.7 100 digits
3.6.8 200 digits
3.6.9 500 digits
3.6.10 1000 digits
3.7. Automatic taring:
first weight tared
3.7.1* Off
3.7.2 On
3.17. Automatic individual or compo-
nent printout when value stored
3.17.1 Off
3.17.2* Generate printout with
complete standard
configuration each time
O is pressed
3.17.3 Generate printout with
complete standard
configuration only the
first time O is pressed
3.25. Tare function
3.25.1* Add input value (weigh
value) for taring
3.25.2 Tare value can be
overwritten
* = Factory setting
§ Press ) to save your settings and (
(repeatedly) to exit the operating menu.
Minimum Load
The minimum amount that a compo-
nent must weigh before it can be saved
in net-total memory is configured in
the operating menu under:
appl R: 3.6.
Once the limit is exceeded by the load,
the value can be saved. If the load
is too light, the following will occur
when you try to save a value:
– The error code
Inf 29 is displayed
– The weighing platform is not initialized
The minimum load required for auto-
matic taring of the container weight
on the platform (“autotare first weight")
is configured in the operating menu
under:
appl R: 3.5.
You can choose from 10 settings,
ranging from
1 digit
to
1000 digits
Example: If the scale interval (d) is
1000 g and the minimum load is set
to 1000 digits (=1000 scale intervals),
a load of at least 1000 g is required
for autotaring.
Tare function:
1) If you store a tare (weight value) by
pressing the ) key, you can later
enter a tare value manually. The tare
value you enter is added to the stored
tare value.
Setting: menu code
3.25.1
(factory default)
2) A tare value entered manually over-
writes a stored tare value (weight
value). if you enter a tare value manu-
ally, a tare value (weight value) stored
later overwrites the manually entered
value.
Setting: menu code
3.25.2
Operating menu setting:
appl R: 3.25.
79
To Next Page
Loading...
Need help?
General
