First edition: Mar 2014 Q04502000
©2014 SATO CORPORATION
UHF Inlay Configuration Guide
CL4NX UHF Inlay Placement & Configuration Table
This recommendation has been tested successfully at SATO. Results may vary in the actual customer installation due to overall system tolerances. Validation of
functionality in the actual system is therefore recommended.
In no event shall SATO be liable for any faults arising out of use of or inability to use the product.
Position(mm) Power (dBm)
(Y=) Standard Antenna Position
(mm)
Region
Manufacturer
Inlay
[IC Chip]
Feed Direction
XYSWriteRead
Antenna
Pitch
Blue Yellow Green
Alien
Technology
ALN-9640 “Squiggle”
[Alien Higgs3]
47.5-57 3-5 21 24 14 Short - - -
47.5-57 18-36 33 16 7 Standard
18-23 24-29 30-36
Alien
Technology
ALN-9662 “Short”
[Alien Higgs3]
35-45 0-5 23 24 18 Short - - -
35-65 10-24 50 24 16 Standard
10-14 15-20 21-24
Alien
Technology
ALN-9762 “Short”
[Alien Higgs4]
50-60 0-5 20 24 13 Short - - -
50-60 15-22 43 24 10 Standard
15-18 19-22 -
Alien
Technology
ALN-9610 “Squig”
[Alien Higgs3]
22.5-42 2-5 21 24 13 Short - - -
22.5-62 15-24 85 24 15 Standard
15-18 19-24 -
Alien
Technology
ALN-9710 “Squig”
[Alien Higgs4]
22.5-62 3-6 21 24 15 Short - - -
22.5-37 14-28 80 23 20 Standard 14-18 19-24 25-28
Alien
Technology
ALN-9720 “HiScan”
[Alien Higgs4]
19.5-59 0-3 31 24 18 Short - - -
34.5-59 14-32 80 24 17 Standard 14-17 18-24 25-32
Alien
Technology
ALN-9654 “G Tag”
[Alien Higgs3]
46.5-56.5 1-10 25 20 17 Short - - -
46.5-61.5 14-30 58 14 10 Standard
14-18 19-24 25-30
Alien
Technology
ALN-9728
“Garment Tag”
[Alien Higgs4]
22.5-37.5 0-5 36 23 15 Short - - -
22.5-62.5 6-19 105 24 18 Standard
6-9 10-14 15-19
Alien
Technology
ALN-9728-90
“Garment Tag”
[Alien Higgs4]
- - - - - Short - - -
15-35 24-37 85 18 10 Standard
- 24-30 31-37
Alien
Technology
ALN-9730 "Squiglette"
[Alien Higgs 4]
- - - - - Short - - -
55 17-24 26 24 11 Standard
17-20 21-24 -
Alien
Technology
ALN-9630 "Squiglette"
[Alien Higgs 3]
40-55 0-4 22 24 16 Short - - -
40-70 15-33 59 24 17 Standard
15-23 24-28 29-33
Arizon
AZ-9762
[Alien Higgs4]
35-50 0-3 25 24 19 Short - - -
40-65 11-36 48 24 17 Standard
11-19 20-28 29-36
Avery
Dennison
AD-110m5
[Impinj Monza5]
21.5-46.5 4-11 22 24 16 Short - - -
36.5-46.5 11-32 65 24 20 Standard 11-17 18-25 26-32
I-Mark
In order to successfully configure your CL4NX UHF printer,
you will need the following information about your label.
X: Liner Edge to Center of Chip
Y: Optimum Encoding Position*
S: Minimum Inlay Separation
*Y: Measured from tail edge of I-mark to lead edge of inlay when
I-mark sensor is used.
Measured from lead edge of label to edge of inlay when Gap
sensor is used.
Position(mm) Power (dBm)
(Y=) Standard Antenna Position
(mm)
Region
Manufacturer
Inlay
[IC Chip]
Feed Direction
XYSWriteRead
Antenna
Pitch
Blue Yellow Green
Alien
Technology
ALN-9640 Squiggle
[Alien Higgs3]
47.5-57 3-5 21 24 14 Short - - -
47.5-57 18-36 33 16 7 Standard
18-23 24-29 30-36
Alien
Technology
ALN-9662 Short
[Alien Higgs3]
35-45 0-5 23 24 18 Short - - -
35-65 10-24 50 24 16 Standard
10-14 15-20 21-24
Alien
Technology
ALN-9762 Short
[Alien Higgs4]
50-60 0-5 20 24 13 Short - - -
50-60 15-22 43 24 10 Standard
15-18 19-22 -
The value of “Y” will affect printer configuration of
Antenna Selection and Antenna Position.
Feed direction will affect encoding.
This is signified using the inlay
images in the following table.
Standard Antenna Position determined by value of Y.
When Antenna Pitch is “Short”, Standard Antenna Position
can be set to any position; “Blue”, “Yellow”, or “Green”.
Feed Direction
The arrow in the header of table
indicates the direction in which labels
are output from the printer.
Placement and Configurations
globally valid with minor variation.
Valid for Frequencies that fall
within the FCC range, 902-928MHz
CL4NX_Inlay_CG.fm Page 39 Monday, March 10, 2014 7:53 PM
To Next Page
Need help?
General
