How to resolve a BCC check error on a SATO Label Maker?
If you encounter a BCC check error on your SATO Label Maker, it means the BCC code of the data to be sent is incorrect. Check the data to be sent and the communication settings. You can either continue printing from the point of the error using the LINE button, or clear the error and continue from where it stopped by sending the SUB command.
Why am I getting a download data error on my SATO s86ex?
A download data error on your SATO Label Maker can occur if the downloaded data is incorrect or if the download area is insufficient. Check the downloaded data and the downloaded data size.
What to do if my SATO s86ex Label Maker shows a 'Paper end' error?
If your SATO Label Maker displays a 'Paper End' error, it means the media is either not loaded, not loaded correctly, has jammed, or the media sensor is dirty or has a disconnected cable. First, load the media correctly and remove any jammed media. Then, clean the media sensor and ensure its cable is correctly connected. You may also need to adjust the sensor level.
What causes a 'Saver error' on my SATO s86ex?
If your SATO Label Maker displays a 'Saver error', it means the print head cannot stop at the specified position. Adjust the saver head position. Replace the saver sensor. Replace the saver motor and motor driver PCB. Replace the saver cam.
What does Item No. error mean on SATO s86ex Label Maker?
An Item No. error on your SATO Label Maker indicates that the sequence number of the print data is not increased by one, meaning the sequence is not in sequential order. Check the data to be sent and the communication settings. You can continue printing from the point of the error using the LINE button, or clear the error and continue from where it stopped by sending the SUB command.
What causes a 'Machine error' on my SATO Label Maker?
If your SATO Label Maker shows a 'Machine error', it is caused by a defective circuit board. Replace the main (CONT) PCB.
How do I resolve a sensor error on my SATO s86ex Label Maker?
A sensor error on your SATO Label Maker could be due to an incorrect media sensor level, the wrong sensor type, or meandering media. Adjust the media sensor level, ensure you are using the correct sensor type, and clean and adjust the media path.
Why is my SATO s86ex Label Maker showing a memory write error when using USB memory?
A memory write error on your SATO Label Maker when using USB memory can occur for several reasons. The USB memory might be disconnected during writing, or there might not be sufficient copy area in the memory. Also, writing to the memory may fail, or the USB memory might not be formatted. Ensure the USB memory is connected, has sufficient copy area, and is properly formatted. If the issue persists, try replacing the memory.
What causes a 'Flash ROM error' on my SATO Label Maker?
If your SATO Label Maker displays a 'Flash ROM error', it means the Flash ROM is not accessible. Replace the main (CONT) PCB.
What to do if my SATO Label Maker displays a 'Sensor cover open error'?
If your SATO Label Maker displays a 'Sensor cover open error', it means the sensor cover is unlocked or the sensor for sensing the open/close status of the sensor cover is defective. Ensure the sensor cover is locked. If the error persists, the sensor may need to be replaced.
Provides essential safety and environmental guidelines for printer installation.
Step-by-step guide for correctly loading the ribbon into the printer.
Overview of the printer's LCD display and operational controls and status icons.
Lists and describes the various operating modes available on the printer.
Guides users on accessing and configuring the printer via a web browser interface.
Step-by-step guide for cleaning the print head and platen roller.
Explains printer error messages, their causes, and recommended countermeasures.
Explains printer warning messages, their causes, and countermeasures.
A table listing common printer operational issues and their solutions.
General| Print Technology | Thermal Transfer / Direct Thermal |
|---|---|
| Print Resolution | 305 dpi |
| Maximum Print Length | 39.37 inches |
| Media Thickness | 0.0025 to 0.01 inches |
| Media Type | Roll |
| Connectivity | USB, Ethernet, Serial, Parallel |
| Operating System Compatibility | Windows, Linux |
| Supported Barcode Types | QR Code, PDF417 |
| Power Supply | AC 100-240V, 50/60 Hz |
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
| Storage Temperature | -4 to 140°F |
| Humidity | 25% to 85% RH, non-condensing (Operating and Storage) |
To Next Page
