What to do if my SATO Label Maker displays a 'Sensor cover open error'?
If your SATO Label Maker displays a 'Sensor cover open error', it means the sensor cover is unlocked or the sensor for sensing the open/close status of the sensor cover is defective. Ensure the sensor cover is locked. If the error persists, the sensor may need to be replaced.
What to do if my SATO Label Maker displays a 'Parity error'?
If your SATO Label Maker displays a 'Parity error', 'Overrun error', or 'Framing error', it is likely due to incorrect RS-232C settings or an incorrect cable connection. Adjust the interface settings correctly and ensure the cable is properly connected.
How to fix SD card write error on SATO Label Maker?
If you're encountering an SD card write error on your SATO Label Maker, start by ensuring the SD card is properly connected. If it is, verify that it isn't write-protected; if it is, release the write-protect. If the issue continues, the SD card may need to be replaced.
Why does my SATO s86ex say ribbon end?
The 'Ribbon End' error on your SATO Label Maker typically means that the ribbon is either not loaded, not loaded correctly or damaged. Try loading a new ribbon or ensuring that the existing ribbon is correctly loaded. If the ribbon is torn, clean and adjust the ribbon path.
What to do if SATO s86ex Label Maker shows head open error?
If your SATO Label Maker displays a 'Head Open' error, it indicates that the print head is unlocked. Make sure to lock the print head. If the problem persists, the sensor for sensing the open/close status of the print head might be defective and needs replacement.
What causes an overheat error on a SATO s86ex Label Maker?
An overheat error on your SATO Label Maker occurs when the printer's temperature exceeds its tolerance value. To resolve this, stop using the printer and allow it to cool down.
What to do when SATO s86ex Label Maker displays a memory full error?
If your SATO Label Maker shows a 'Memory Full Error', it means that there is not enough space in the memory. To fix this, delete any unnecessary data from the memory.
What causes a buffer overflow on a SATO s86ex?
A buffer overflow on your SATO Label Maker happens either because the received data's size is too large for the receive buffer, or the communication settings between the printer and the host are incorrect. Avoid sending data exceeding the buffer size, and ensure the communication settings between the printer and the host are correctly configured.
How do I resolve a sensor error on my SATO s86ex Label Maker?
A sensor error on your SATO Label Maker could be due to an incorrect media sensor level, the wrong sensor type, or meandering media. Adjust the media sensor level, ensure you are using the correct sensor type, and clean and adjust the media path.
Why is my SATO s86ex Label Maker showing a memory write error when using USB memory?
A memory write error on your SATO Label Maker when using USB memory can occur for several reasons. The USB memory might be disconnected during writing, or there might not be sufficient copy area in the memory. Also, writing to the memory may fail, or the USB memory might not be formatted. Ensure the USB memory is connected, has sufficient copy area, and is properly formatted. If the issue persists, try replacing the memory.
Provides essential safety and environmental guidelines for printer installation.
Step-by-step guide for correctly loading the ribbon into the printer.
Overview of the printer's LCD display and operational controls and status icons.
Lists and describes the various operating modes available on the printer.
Guides users on accessing and configuring the printer via a web browser interface.
Step-by-step guide for cleaning the print head and platen roller.
Explains printer error messages, their causes, and recommended countermeasures.
Explains printer warning messages, their causes, and countermeasures.
A table listing common printer operational issues and their solutions.
General| Print Technology | Thermal Transfer / Direct Thermal |
|---|---|
| Print Resolution | 305 dpi |
| Maximum Print Length | 39.37 inches |
| Media Thickness | 0.0025 to 0.01 inches |
| Media Type | Roll |
| Connectivity | USB, Ethernet, Serial, Parallel |
| Operating System Compatibility | Windows, Linux |
| Supported Barcode Types | QR Code, PDF417 |
| Power Supply | AC 100-240V, 50/60 Hz |
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
| Storage Temperature | -4 to 140°F |
| Humidity | 25% to 85% RH, non-condensing (Operating and Storage) |
To Next Page
