Scania DC16 XPI - Page 106

128 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

OPM 300 en-GB 106

© Scania CV AB 2020, Sweden

Other

8.

Check that the seal protecting the reductant

doser from radiated heat is undamaged and is

in place.

9. Fit the end plate.

• Fit the end plate.

• Secure the electrical cables and any reductant

hoses with heat-resistant cable ties.

341 447

417 292

Table of Contents

Default Chapter2
- Table of Contents2
Start of Warranty3
Scania Engines Engine Warranty for Industrial Checking the Coolant's Antifreeze and Corrosion4
Engines4
- Emission Control Systems Warranty4
- Emission Control System Warranty Statement4
- General Warranty Provisions4
- Warranty Period4
- Parts Covered by the Warranty5
- General Warranty Limitations6
- Specific Warranty Exclusions7
- Customer Support7
California Emission Control Warranty Statement8
- Your Warranty Rights and Obligations8
- Manufacturer's Warranty Coverage8
- Owner's Warranty Responsibilities8
SCR Catalytic Converter9
Introduction11
Certification11
Power Classes12
Environment and Safety14
- Environmental Responsibility14
- Safety14
- Warnings and Advisories15
Engine Data Plate20
Component Identification21
- Engine21
- SCR System22
- Stage V23
Starting and Running24
- Checks before First Start24
- Checks before Running25
- Starting the Engine26
- Running26
- Engine Shutdown34
- Checks after Running35
- Transporting Engines35
Maintenance36
- Engines with few Hours of Operation38
- Cleaning the Engine38
- Maintenance Interval39
- Particulate Filter Maintenance Intervals40
Lubrication System41
- Oil Grade41
- Oil Analysis45
- Checking the Oil Level46
- Maximum Angles of Inclination During Operation46
- Changing the Oil47
- Cleaning the Centrifugal Oil Cleaner48
- Operational Testing of the Centrifugal Oil Cleaner52
- Renewing the Oil Filter53
Air Cleaner54
- Reading the Vacuum Indicator54
- Renewing the Air Cleaner Filter Element and Safety Cartridge55
Cooling System56
- Coolant56
- Checking the Coolant Level61
- Checking the Coolant's Antifreeze and Corrosion Protection62
- Changing the Coolant and Cleaning the Cooling63
- System63
Fuel System71
- Cleanliness Requirements71
- Checking the Fuel Level72
- Renewing the Fuel Filters73
- Bleeding the Fuel System80
Other82
- Checking the Drive Belt82
- Checking for Leakage83
- Checking and Adjusting the Valve Clearance84
- Renewing the Reductant Filter87
- Cleaning the Reductant Tank Filler Filter90
- Cleaning the Reductant Tank Ventilation Filter.9090
- Cleaning the Reductant Tank91
- Renewing the Particulate Filter92
Quality Requirements for Fuel98
- Diesel98
- Biodiesel (FAME)101
- Hvo102
- Gtl102
Reductant for SCR103
Preparing the Engine for Storage104
- Preservative Products104
- Preparations for Storage105
Technical Data107
- General Data107
- Lubrication System107
- Intake System108
- Cooling System108
- Fuel System108
- Electrical System108
Scania Assistance109
General Tightening Torques for Screw Joints110
- Hexagon Screws, Hexagon Socket Screws, Torx Screws, Hexagon Nuts110
- Flange Screws with Hexagonal Head and Hexago- Nal Flange Nuts110
- Hose Clamps111

Related product manuals

Preview: Scania DC16

Scania DC13 XPI

Preview: Scania DI13 XPI

Scania DI13 XPI

Scania DI16 XPI series

Preview: Scania DC11

Preview: Scania DC12

Scania DC13 074

Scania DC13 085

Preview: Scania DC13 070A

Scania DC13 070A

Scania DC13 072A

Scania DC13 071A