www.scheppach.com
GB
|
31
Speed n
max
................................................. 12000 rpm
Spark plug ....................................................... L8RTC
* The actual cutting length may be less than the spec-
ied cutting length.
Noise
Sound pressure level L
pA
per ISO 22868 ... 98,9 dB(A)
Uncertainty K
pA
................................................. 2,5 dB
Sound power level L
WA
per ISO 22868 ........................................113,28 dB(A)
Uncertainty K
WA
................................................. 2,5 dB
Wear hearing protection.
Excessive noise can result in a loss of hearing.
The specied device emissions values have been
measured in accordance with a standardised test pro-
cedure and can be used for the comparison of one
tool with another.
The specied noise emission values can also be used
for an initial estimation of the exposure.
Vibration
Vibration value at the rear
Handle per ISO 22867 ................................5,277 m/s
2
Vibration value at the front
Handle per ISO 22867 ................................6,185 m/s
2
Uncertainty K ..................................................1.5 m/s
2
m WARNING
Avoid the risks associated with vibration, e.g. the risk
of white nger syndrome (circulatory disorders) by
taking frequent breaks from work where you rub your
palms together, for example.
8. Before commissioning
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of
the warranty period.
ATTENTION
The device and the packaging are not children‘s toys!
Do not let children play with plastic bags, lms or small
parts! There is a danger of choking or suocating!
contact with the rail tip, and enable improved control
of the chainsaw in unexpected situations.
■ Always use replacement guide rails and saw chains
prescribed by the manufacturer. Incorrect replace-
ment guide bars and saw chains may cause the
saw chain to break and/or lead to kick-back.
■ Adhere to the instructions of the manufacturer when
sharpening and maintaining the saw chain. If the
depth limiter is too low, this increases the tendency
towards kick-back.
■ Do not saw with the tip of the guide bar. There is a
risk of kick-back.
■ Make sure that there are no nails or metal pieces
in the cutting area. Pay special attention to nails or
pieces of iron around the cutting area. Also be care-
ful when sawing hardwoods where the chain can
get caught. This can cause kick-back.
■ Start cutting at full power and always keep the
chainsaw at maximum speed while sawing.
■ Make sure that there are no objects on the oor that
you can trip over.
6.9 Residual risks
m DANGER
RISK OF INJURY !
Contact with the saw chain can lead to fatal cuts.
Never touch the saw chain with your hands while it is
running.
RISK OF KICK-BACK !
Kick-back can lead to fatal cuts.
DANGER OF BURNING !
The chain and guide bar heat up during operation.
7. Technical data
Weight unfuelled, without cutting gear approx. ..5,2 kg
Weight unfuelled, with cutting gear approx. ......6.4 kg
Fuel tank ............................... approx. 550 cm
3
(0.55 l)
Tank for chain lubricating oil . approx. 260 cm
3
(0.26 l)
Usable cutting length* /
Guide rail .................................................. 45 cm (18”)
Max. chain speed ..............................................22m/s
Chain pitch.......................................8.25 mm (0.325”)
Driving link thickness ......................... 1.5 mm (0,059”)
Type of saw chain KANGXING
(pre-assembled): ....................................325-058-72T
Type of guide bar KANGXING
(pre-assembled): ..............................BE18-72-5810P
Chain wheel tooth pitch ...7 teeth / 8.255 mm (0.325”)
Engine displacement ........................................45 cm
3
Max. engine power output per ISO 7293 ......... 1,8 kW
Idle speed n
0
...................................... 3000 ± 300 rpm
To Next Page
Loading...
Need help?
General
