To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Why Scheppach Saw motor makes excessive noise?
If your Scheppach Saw motor makes excessive noise, it could be due to damaged coils or a defective motor. Arrange for inspection of the motor by a specialist.
Why workpiece pulls away and/or splinters when using my Scheppach Saw?
If the workpiece pulls away and/or splinters when using your Scheppach Saw, it's likely due to excessive cutting pressure or using a saw blade that isn't suitable for the task. Insert a suitable saw blade.
Why burn marks appear on the wood during cutting with my Scheppach HBS30 Saw?
Burn marks appearing on the wood during cutting with your Scheppach Saw can be caused by a blunt or wrong saw blade. Change the saw blade and select a saw blade according to the operating instructions.
Why does my Scheppach HBS30 Saw motor overheat?
The Scheppach Saw motor might overheat easily due to overloading or insufficient cooling. To resolve this, avoid overloading the motor while cutting and remove dust from the motor to ensure optimal cooling.
What to do if the Scheppach HBS30 Saw blade jams during cutting?
If the saw blade of your Scheppach Saw jams during cutting work, it could be due to a blunt saw blade, deposits on the saw blade, or a poorly set guide. You should change the saw blade, clean the saw blade, and set the saw blade guide according to the operating instructions.
Why Scheppach HBS30 motor does not reach its full power?
If your Scheppach Saw motor isn't reaching its full power, it could be due to loaded circuits in the network (lamps, other motors, etc.). Avoid using other equipment or motors on the same circuit.
Why does my Scheppach Saw motor overheat easily?
If your Scheppach Saw motor overheats easily, it might be due to overloading or insufficient cooling. To resolve this, avoid overloading the motor during cutting. Also, remove any dust from the motor to ensure optimal cooling.
How to fix Scheppach HBS30 Saw blade that is not running straight?
If the Scheppach Saw blade is not running straight, it could be because the guide has been wrongly set or the wrong saw blade is being used. Set the saw blade guide according to the operating instructions. Select a saw blade according to the operating instructions.
Why does my Scheppach Saw motor make excessive noise?
If the Scheppach Saw motor is making excessive noise, it could be because the coils are damaged or the motor is defective. Arrange for inspection of the motor by a specialist.
Why does the workpiece pull away or splinter when using my Scheppach HBS30 Saw?
If the workpiece pulls away or splinters when using your Scheppach Saw, it may be due to excessive cutting pressure or a saw blade not suitable for use. Try inserting a suitable saw blade.
General| Product type | Vertical band saw |
|---|---|
| Product color | Blue, Grey |
| Built-in light | - |
| Adjustable speed | Yes |
| Housing material | Steel, Aluminium |
| Table bevel angle | 0 - 45 ° |
| Input power | 350 W |
| Power source | AC |
| AC input voltage | 230 - 240 V |
| AC input frequency | 50 Hz |
| Cutting width | - mm |
| Cutting height @ 90° | 80 mm |
| Number of teeth per inch (TPI) | 6, 10, 15 |
Weight and Dimensions| Depth | 730 mm |
|---|---|
| Width | 420 mm |
| Height | 540 mm |
| Weight | 20500 g |
| Table depth | 520 mm |
| Table width | 300 mm |
Key safety measures for operating and maintaining the electric tool.
Lists potential risks and remaining hazards associated with the machine's use.
Lists the necessary tools for assembly and setup.
Step-by-step guide for attaching the saw table to the machine.
Instructions for attaching the table extension for wider workpieces.
Guide on how to attach and adjust the parallel fence for precise cuts.
Steps for aligning the saw band on the band wheels for optimal cutting.
How to set the upper and lower saw band guides for proper blade support.
Setting the upper saw band guide pins for blade alignment.
Tilting the saw table to achieve a precise 90-degree angle.
Guidance on selecting the appropriate saw band for different cuts.
Detailed steps for safely removing and installing a new saw band.
Instructions for operating the machine's power switch.
How to perform angled cuts by tilting the saw bench.
Step-by-step guide for cutting wood along its length.
Techniques for cutting curves and radii without guides.
