Scheppach HMS850 - User Manual

Other manuals for Scheppach HMS850

Original Instruction Manual124 pages

Translation From The Original Instructions172 pages

Operating And Safety Instructions40 pages

Translation Of Original Instruction Manual136 pages

Questions and Answers

D
Dr. Christina HarrisAug 25, 2025
What to do if my Scheppach HMS850 stops working suddenly?
- A
  amanda50Aug 25, 2025
  If your Scheppach Planer stops suddenly or doesn't work, consider these potential issues: * **Power cut**: Check the fuse and the overload switch on the machine. * **Defective motor or switch**: Have an electrician inspect the motor or switch. * **Microswitch issue**: Ensure the chip extractor hood is correctly fitted to press the microswitch. * **Low voltage protection**: If the voltage returns after an interruption, you will need to manually switch the machine back on because it won't restart automatically.
N
Noah AcostaAug 25, 2025
How to resolve chip ejection obstruction during thicknessing with Scheppach HMS850 Planer?
- K
  Katie ReyesAug 26, 2025
  If chip ejection is obstructed during thicknessing with your Scheppach Planer (without a dust extractor), consider the following: * **Too much chip removal**: Reduce the amount of chip removal. * **Blunt knives**: Replace the knives. * **Wood too humid**: Dry the workpiece.
E
Emily JonesAug 26, 2025
Why is chip ejection obstructed in Scheppach Planer even with dust extractor?
- T
  Tiffany BrownAug 26, 2025
  If chip ejection is obstructed during surface planing and thicknessing, even with a dust extractor connected to your Scheppach Planer, the suction performance might be too weak. Use a dust extractor unit having an airflow rate at the suction connection of at least 20 m/s.
D
diana78Aug 26, 2025
Why does the Scheppach HMS850 speed decrease?
- A
  april16Aug 27, 2025
  If the Scheppach Planer speed decreases when planing, it could be due to too much chip removal, so reduce it. Alternatively, the feed may be too fast, so reduce the infeed speed. Blunt knives can also cause this issue, so replace them.
A
Amy LambAug 27, 2025
Why Scheppach HMS850 machine cannot be switched on?
- F
  floresstephanieAug 27, 2025
  If your Scheppach Planer machine cannot be switched on, it could be due to several reasons. First, check the power supply to ensure it is working. Second, the carbon brush might be worn, in that case, take the machine to your service point. Third, the chip extractor might not be mounted.
B
brownphillipAug 27, 2025
Why does my Scheppach HMS850 Planer's speed decrease when planing?
- J
  Julie JohnstonAug 27, 2025
  If the speed of your Scheppach Planer decreases during planing, it could be due to several reasons. You might be removing too much material, so reduce the chip removal. Alternatively, the feed might be too fast, so reduce the infeed speed. Also, blunt knives can cause this issue, so replace them.
K
Kristin JohnsonAug 27, 2025
What causes obstructed chip ejection during thicknessing (without dust extractor) in Scheppach HMS850?
- L
  Lori FuentesAug 27, 2025
  If you experience obstructed chip ejection during thicknessing (without a dust extractor) when using your Scheppach Planer, it could be due to a few reasons. You might be removing too much material, so reduce the chip removal. The knives could also be blunt, so replace them. Additionally, the wood may be too humid, so dry the workpiece.
D
Dana BennettAug 28, 2025
What causes obstructed chip ejection during surface planing (without dust extractor) in Scheppach HMS850?
- M
  Mark MorrowAug 28, 2025
  If you experience obstructed chip ejection during surface planing (without a dust extractor) when using your Scheppach Planer, several factors could be the cause. You might be removing too much material, so reduce the chip removal. The feed might be too fast, so reduce the infeed speed. The knives could also be blunt, so replace them. Finally, the wood may be too humid, so dry the workpiece.
H
Hector WilliamsonAug 28, 2025
How to troubleshoot a Scheppach Power Tool that cannot be switched on?
- A
  Adam CaseAug 28, 2025
  If your Scheppach Power Tool won't switch on, start by checking the power supply. If the power supply is working, the carbon brush might be worn, requiring you to take the machine to your service point for assistance. Also, ensure the chip extractor is mounted.
D
Daisy GravesAug 29, 2025
Why my Scheppach Planer cannot be switched on?
- B
  brandy15Aug 29, 2025
  If your Scheppach Planer cannot be switched on, there are a few potential reasons. First, check the power supply. Second, the carbon brush might be worn, requiring you to take the machine to your service point. Third, the chip extractor might not be mounted, also requiring you to take the machine to your service point.

Scheppach HMS850 Specifications

General

Motor Power	1250 W
Planing Width	204 mm
Max Planing Depth	2 mm
Max Thicknessing Height	120 mm
Feed Rate	8 m/min
Table Size	737 x 210 mm
Cutter Block Speed	8000 rpm
Thicknessing Width	204 mm
Motor	230 V, 50 Hz