Scheppach HMS850 - User Manual

Other manuals for Scheppach HMS850

Original Instruction Manual124 pages

Translation From The Original Instructions172 pages

Operating And Safety Instructions40 pages

Translation Of Original Instruction Manual136 pages

Questions and Answers

J
Joseph MartinSep 4, 2025
Why does my Scheppach Planer stop during planing?
- A
  Amanda JamesSep 4, 2025
  If the Scheppach Planer stops during planing, it could be due to several reasons. The planing blade might be blunt or worn, in which case you should replace or sharpen it. The overload switch may have tripped; if so, switch on the motor again once it has cooled. Also, ensure the chip extractor hood or bench lock is fitted correctly so that the microswitch is pressed. Other potential causes include too much chip removal (reduce it) or too fast feed (reduce infeed speed).
A
Allison HansenSep 4, 2025
What to do if my Scheppach HMS850 does not work?
- P
  Paul HortonSep 4, 2025
  If the Scheppach Planer machine does not work or stops suddenly, check the fuse for a power cut. If the motor or switch is defective, have it checked by an electrician. Ensure the chip extractor hood is fitted correctly to press the microswitch. Due to the integrated low-voltage protection, the machine does not restart automatically; upon return of voltage, switch the machine on again.
C
Caleb BrownSep 5, 2025
Why is the machined surface cracked with my Scheppach HMS850 Planer?
- J
  jennifer19Sep 5, 2025
  If the machined surface is cracked when using the Scheppach Planer, it could be because the workpiece was machined against the grain. Try machining the workpiece from the opposite direction. Also, too much material planed at one pass can cause this, so machine the workpiece in several passes.
H
hartaustinSep 5, 2025
Why is the machined surface too rough with my Scheppach Planer?
- C
  Christina CurrySep 5, 2025
  If the machined surface is too rough when using the Scheppach Planer, it's likely because the workpiece contains too much moisture. Dry the workpiece before machining.
S
Scott CruzSep 6, 2025
What to do if my Scheppach Planer stops during planing?
- H
  Henry ReidSep 6, 2025
  If your Scheppach Planer stops during planing, several factors could be the cause. The planing blade might be blunt or worn, in which case you should replace or sharpen it. The overload switch may have tripped; if so, switch the motor on again once it has cooled. Also, check the microswitch and ensure the chip extractor hood or bench lock is fitted correctly so that the microswitch is pressed. Finally, you might be removing too much material or feeding too quickly, so reduce the chip removal and infeed speed.
A
angela54Sep 6, 2025
What to do if my Scheppach Planer machine does not work or stops suddenly?
- C
  christine74Sep 6, 2025
  If your Scheppach Planer machine does not work or stops suddenly, there are several potential causes. Check the fuse and the overload switch on the machine, as there may be a power cut. The motor or switch may be defective, in that case, have them checked by an electrician. Also, check the microswitch and fit the chip extractor hood so that the microswitch is pressed. Finally, check the fuses and upon return of the voltage, the machine must be switched on again.
J
Jason CooperSep 7, 2025
Why is the surface finish unsatisfactory with my Scheppach HMS850?
- S
  Sydney WestSep 7, 2025
  An unsatisfactory surface finish with your Scheppach Planer can occur for a few reasons. The planing blade might be blunt or worn, so replace or sharpen it. The planing blade could also be filled with chips; if so, remove them. Uneven feed can also cause this, so feed the workpiece with constant pressure and at a reduced speed.
C
Christina MooreSep 7, 2025
What causes a machined surface to be too rough when using a Scheppach HMS850 Planer?
- C
  craigmelissaSep 7, 2025
  If the machined surface is too rough when using your Scheppach Planer, it could be because the workpiece contains too much moisture. In this case, dry the workpiece.

Scheppach HMS850 Specifications

General

Motor Power	1250 W
Planing Width	204 mm
Max Planing Depth	2 mm
Max Thicknessing Height	120 mm
Feed Rate	8 m/min
Table Size	737 x 210 mm
Cutter Block Speed	8000 rpm
Thicknessing Width	204 mm
Motor	230 V, 50 Hz