What to do if my Schumacher EV Battery Charger shows overvoltage?
If your Schumacher Battery Charger shows an overvoltage fault, first, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the problem persists, it is recommended to consult a licensed electrician to check the AC supply.
What to do if my Schumacher EV shows undervoltage?
If your Schumacher Battery Charger is showing an undervoltage fault, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the fault continues, it is recommended to consult a licensed electrician to check the AC supply.
What to do if my Schumacher Battery Charger has a ground fault?
If your Schumacher Battery Charger is experiencing a ground fault, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the issue continues, it is recommended to consult a licensed electrician to check the ground connection.
What to do if my Schumacher EV shows overcurrent?
If your Schumacher Battery Charger is showing an overcurrent fault, unplug the charging gun and then reinsert it into your vehicle’s charging port.
What to do if my Schumacher EV Battery Charger says 'over temperature'?
If your Schumacher Battery Charger displays an 'over temperature' message, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the problem continues, unplug the charging gun and allow the unit to cool down before attempting to charge again.
How to troubleshoot no AC power on my Schumacher EV Battery Charger?
If your Schumacher Battery Charger has no AC power, check the breaker. It is also recommended to have a licensed electrician connect the charging station to AC power.
What to do if my Schumacher EV has leakage?
If your Schumacher Battery Charger experiences a leakage issue, re-power the unit by turning the circuit breaker off and on again. If the fault still exists, please consult a licensed electrician for help or contact our support service.
What to do if my Schumacher EV Battery Charger shows a frequency fault?
If your Schumacher Battery Charger is showing a frequency fault, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the fault continues, it is recommended to consult a licensed electrician to check the AC supply.
What to do if my Schumacher EV Battery Charger has a meter chip fault?
If your Schumacher Battery Charger is experiencing a meter chip fault, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the issue persists, contact our support service.
What to do if my Schumacher EV Battery Charger has a relay fault?
If your Schumacher Battery Charger has a relay fault, unplug the charging gun and then reinsert it into your vehicle’s charging port. If the issue continues, contact our support service.
Details the mandatory grounding requirements for safe connection of the EV charger.
Specifies that installation and electrical setting changes must be performed by a licensed electrician.
Crucial instruction to turn off power before installation to prevent injury or death.
Guide for feeding and connecting the output cable wires to the correct terminal blocks.
Tasks for a licensed electrician, including breaker sizing and DIP switch settings.
Locating the 8-position DIP switch selector on the electronic board.
Table showing DIP switch combinations for setting maximum output current and power.
Explains the role of the CT coil as a sensor for Dynamic Power Management.
Guidance on attaching and connecting the CT coil to the main cable and charger.
Steps for connecting the CT coil's unsheathed and shielded cables to the charger's terminal blocks.
Reminder that correct installation requires calibration of the maximum charge current.
Table detailing DIP switch combinations for various CT coil turns ratios and current ratings.
Comprehensive table detailing DIP switch settings based on CT coil turns ratio and DLM current rating.
Solutions for issues related to the Power LED being off, typically indicating no AC power.
Troubleshooting steps for specific red flashing codes of the Charging Status LED, indicating various faults.
General| Brand | Schumacher |
|---|---|
| Model | EV Series |
| Category | Battery Charger |
| Language | English |
To Next Page