INSTRUCTIONS FOR:
FLYWHEEL LOCKING TOOL
MODEL NO: VSE2394
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. APPLICATIONS
WARNING! Ensure all health and safety, local authority and general workshop practice
regulations are strictly adhered to when using tools.
DO NOT use tools if damaged.
Maintain tools in good and clean condition for best and safest performance.
If required, ensure the vehicle to be worked on is adequately supported with axle
stands, ramps and chocks.
Wear approved eye protection. A full range of personal safety equipment is available
from your Sealey dealer.
Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
Account for all tools, locking bolts, pins and parts being used and do not leave them in or
near the engine.
IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or proprietary
manual to establish the current procedure and data.
These
instructions for use are
provided as a guide only .
It is often necessary to remove the crankshaft pulley when replacing the timing belt. The pulley
retaining bolt is tted with a high torque loading and the ywheel must be securely locked during
installation/removal. Jamming tools into the teeth of the ywheel will cause serious damage to
both teeth and housing. This locking tools securely locates in the teeth and xes to the housing
using manufacturer's guidelines. Suitable for petrol and diesel engines.
VSE2394
CITROEN: Synergie 2.0/Turbo, ZX 1.9D/TD, Xantia 1.9D/TD, Berlingo 1.9D, Dispatch 1.9D/TD, Synergie 1.9D, Relay 1.9D/TD.
FIAT: Ulysse 2.0/Turbo, Ducato 2.0
.
FSO 1.9D.
LDV: 200 1.9D, Pilot 1.9D.
PEUGEOT:
205 1.6/1/9, 305 1.6/1.9, 309 1.6/1.9,
405 1.6/1.9, 405 1.8/2.0 (92-), 605 2.0, Boxer 2.0,c205 1.8/1.9D, 305 1.8/1.9D, 306 1.8/1.9D/TD,
309 1.8/1.9D1.8TD, 405 1.8TD, 405 1.9D, 406 1.9D, Partner 1.9D, Talbot/Horizon/Solara 1.9D, J5/Talbot Express 1.9D,
605D/TD, 806 1.9TD, Expert 1.9D, Boxer 1.9D/TD.
RENAULT:
R5 1.6D, R9 1.6D, 411 1.6D Express/Extra 1.6D - F8M Diesel engines.
Clio, Express/Extra, R19 1.9D - early F8Q Diesel engines.
Espace 2.1D, R21 2.1D, R25 2.1D, Trafic/Master 2.1D - J8S Diesel engines
Clio 1.2/1.4, Express/Extra, R19 1.4, Megane/Scenic 1.4/1.6-E7F/E7J/ Petrol engines.
R5, 1.7, Clio 1.7/1.8, R19 1.7, R21 1.7, Megane/Scenic 2.0, Laguna 1.8/2.0, Trafic 1.7 - F3N/F3P/F2R Petrol engines.
Clio Williams, R19, Megane 2.0 16V Twin cam F7P/F7R engines
Laguna/Safrane 2.0 16V Twin cam N7Q/N7U engines.
4. INSTRUCTIONS
VSE2394 is used to prevent the crankshaft from rotating when removing the crankshaft pulley for
timing belt replacement. Teeth on the tool engage with the flywheel teeth when the tool is bolted
to the transmission housing to prevent movement of the flywheel (fig.1).
g.1
To Next Page
Need help?
General
