Senco FN55AX - User Manual

27 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operating Instructions

F-15/F-16A/F-16S/F-18

(FN65DA/FN65RHA/FN65RHS/FN55AX)

Fusion Cordless Finish Nailers

Table of Contents

Questions and Answers

M
Mr. Thomas DavenportAug 8, 2025
What to do if my Senco Nail Gun runs but will not drive fastener?
- P
  Patrick RamirezAug 8, 2025
  If your Senco Nail Gun runs but won't drive fasteners, the issue could stem from several causes. First, recharge or replace the battery with a fresh one if it's discharged or has a dead cell. Second, if there's a nail jam in the guide body, refer to the operator's manual for instructions on how to clear it. If the tool is overheated, allow it to cool down and insert a fresh battery. Finally, if the driver tip is not located above the fastener, recharge the battery and allow the tool to automatically retract the driver.
B
Brenda GuzmanAug 14, 2025
What to do if my Senco Nail Gun does not drive fasteners to desired depth?
- Z
  zbestAug 14, 2025
  If your Senco Nail Gun isn't driving fasteners to the desired depth, ensure the depth-of-drive is properly set by referring to the operator's manual. Also, make sure you're holding the tool firmly against the workpiece while driving the fastener. If the application is too demanding, consult the operator's manual for appropriate uses.
R
Robert CaldwellAug 20, 2025
How to fix poor feed/tool jamming on my Senco Nail Gun?
- M
  Michael PerezAug 21, 2025
  If you are experiencing poor feed or tool jamming with your Senco Nail Gun, it might be due to debris build-up in the mechanism or the driver tip not being located above the fastener. To resolve this, clean the tool, lubricate the magazine, or install a new Parts Kit.
B
Brianna SmithAug 27, 2025
What to do if my Senco FN55AX Nail Gun does not fully return?
- H
  Heather GarciaAug 27, 2025
  If your Senco Nail Gun does not fully return, it could be due to a weak battery. Try recharging the battery and allow the tool to automatically retract the driver.
A
angela61Sep 1, 2025
Why Senco Nail Gun will not start or runs slowly?
- L
  lalvarezSep 1, 2025
  If your Senco Nail Gun tool will not start or runs slowly, try these steps: * Replace or recharge the battery if it's discharged or has a dead cell. * If the workpiece contact element is jammed, remove the battery and inspect the tool to ensure free movement of the workpiece contact element. * If the workpiece contact element or trigger switches are damaged, return the tool to an authorized SENCO service representative for repair.

Summary

General Safety Rules

Safety Warnings Overview

General warnings and instructions for battery-operated tools.

Work Area Safety Guidelines

Guidelines for maintaining a safe and clean work environment.

Electrical Safety Precautions

Precautions regarding electrical connections and grounding.

Personal Safety and Protection

Personal Safety Measures

Guidelines for user awareness, alertness, and protective equipment.

Service and Tacker Safety

Safety Instructions for Tackers

Specific safety precautions for operating the tacker.

Fusion Tool Safety

Fusion Additional Safety Instructions

Specific safety warnings and dangers related to the Fusion tool.

Tool Use Guidelines

Operator and Bystander Safety

Requirements for operators and bystanders regarding safety glasses and trigger use.

Tool Operation Basics

Selective Actuation Modes

Description of contact and sequential actuation modes.

Contact Actuation Mode Setup

How to select and use the contact actuation mode.

Sequential Actuation Mode Setup

How to select and use the sequential actuation mode.

Tool Operation Modes Detailed

Contact Actuation Methods

Two methods for driving nails in contact actuation mode.

Sequential Actuation Method

Single method for driving nails in sequential actuation mode.

Tool Operation Handling and Jams

Clearing Nail Jams

Procedures for turning off the tool and clearing a jammed fastener.

Battery Charging Procedure

To Charge Battery Instructions

Step-by-step instructions for charging the battery pack.

Accessories and Troubleshooting

Troubleshooting Tool Issues

Diagnoses and corrective actions for common tool problems.

Summary

General Safety Rules

Safety Warnings Overview

General warnings and instructions for battery-operated tools.

Work Area Safety Guidelines

Guidelines for maintaining a safe and clean work environment.

Electrical Safety Precautions

Precautions regarding electrical connections and grounding.

Personal Safety and Protection

Personal Safety Measures

Guidelines for user awareness, alertness, and protective equipment.

Service and Tacker Safety

Safety Instructions for Tackers

Specific safety precautions for operating the tacker.

Fusion Tool Safety

Fusion Additional Safety Instructions

Specific safety warnings and dangers related to the Fusion tool.

Tool Use Guidelines

Operator and Bystander Safety

Requirements for operators and bystanders regarding safety glasses and trigger use.

Tool Operation Basics

Selective Actuation Modes

Description of contact and sequential actuation modes.

Contact Actuation Mode Setup

How to select and use the contact actuation mode.

Sequential Actuation Mode Setup

How to select and use the sequential actuation mode.

Tool Operation Modes Detailed

Contact Actuation Methods

Two methods for driving nails in contact actuation mode.

Sequential Actuation Method

Single method for driving nails in sequential actuation mode.

Tool Operation Handling and Jams

Clearing Nail Jams

Procedures for turning off the tool and clearing a jammed fastener.

Battery Charging Procedure

To Charge Battery Instructions

Step-by-step instructions for charging the battery pack.

Accessories and Troubleshooting

Troubleshooting Tool Issues

Diagnoses and corrective actions for common tool problems.

Senco FN55AX Specifications

General

Brand	Senco
Model	FN55AX
Category	Nail Gun
Language	English

Related product manuals

Preview: Senco FN65DA

Preview: Senco FinishPro 15

Senco FinishPro 15

Preview: Senco FramePro 650

Senco FramePro 650

Senco FINISHPRO 18

Senco FramePro 721

Preview: Senco FramePro 602

Senco FramePro 602

Preview: Senco FramePro 600

Senco FramePro 600

Preview: Senco FinishPro 35

Senco FinishPro 35

Preview: Senco FUSION F-35XP

Senco FUSION F-35XP

Senco FramePro701XP

Preview: Senco FinishPro 18Mg

Senco FinishPro 18Mg

Preview: Senco FinishPro 42XP

Senco FinishPro 42XP