Need help?Do you have a question about the SGS SC24L and is the answer not in the manual?
Read the manual carefully before operating or adjusting the compressor.
Disconnect from mains supply before maintenance. Avoid damp environments.
Avoid carrying compressor when connected or tank is pressurized.
Surfaces may get hot; do not operate with motor housing removed.
Wear safety goggles and ear protection due to high sound levels.
Familiarize with controls, avoid moving parts, dress appropriately, keep area clear.
Always use eye protection (goggles) and hearing protection (earplugs/defenders).
Avoid wet locations, hot surfaces, and directing air stream at people or animals.
Stay alert, do not use for breathing air, disconnect properly, handle cable with care.
Securely attach the wheels to the compressor unit using provided hardware.
Remove travel bungs and fit the oil breather pipe correctly.
Screw the air filter into its designated location.
Ensure ON/OFF switch is OFF, check oil level, and ensure unit is on level ground.
If oil level is low, remove breather plug and fill with specified compressor oil.
Connect an air hose to the quick release coupler and an air tool.
Lift ON/OFF button to start. Compressor runs until pressurized, then stops.
Adjust the regulator to the correct pressure for the air tool using the output gauge.
Push the ON/OFF switch down to stop the compressor.
Depressurize the hose by operating the tool, then drain condensation from the tank.
Compressor controlled by pressure switch; rated pressure set at factory.
Release compressed air via valve for safe restart to prevent motor damage.
Motor has thermal overload protection; let cool and push reset button if activated.
If overload repeats, stop compressor and seek qualified service.
Follow specific cautions regarding parts, electrical safety, and operation.
Ensure lubricating oil is clean and oil level is maintained as per ruler.
Examine and clean air filters monthly, or more often in dusty conditions.
Perform cleaning and oil changes at specified working hour intervals.
Diagram showing numbered components of the air compressor for reference.
Table listing parts with quantities and corresponding part numbers for ordering.
Details of the manufacturer, SGS Engineering (UK) Ltd, and the equipment.
Lists EC Council Directives and harmonized standards the compressor conforms to.
Formal declaration by Company Secretary confirming equipment conformity.
Read the manual carefully before operating or adjusting the compressor.
Disconnect from mains supply before maintenance. Avoid damp environments.
Avoid carrying compressor when connected or tank is pressurized.
Surfaces may get hot; do not operate with motor housing removed.
Wear safety goggles and ear protection due to high sound levels.
Familiarize with controls, avoid moving parts, dress appropriately, keep area clear.
Always use eye protection (goggles) and hearing protection (earplugs/defenders).
Avoid wet locations, hot surfaces, and directing air stream at people or animals.
Stay alert, do not use for breathing air, disconnect properly, handle cable with care.
Securely attach the wheels to the compressor unit using provided hardware.
Remove travel bungs and fit the oil breather pipe correctly.
Screw the air filter into its designated location.
Ensure ON/OFF switch is OFF, check oil level, and ensure unit is on level ground.
If oil level is low, remove breather plug and fill with specified compressor oil.
Connect an air hose to the quick release coupler and an air tool.
Lift ON/OFF button to start. Compressor runs until pressurized, then stops.
Adjust the regulator to the correct pressure for the air tool using the output gauge.
Push the ON/OFF switch down to stop the compressor.
Depressurize the hose by operating the tool, then drain condensation from the tank.
Compressor controlled by pressure switch; rated pressure set at factory.
Release compressed air via valve for safe restart to prevent motor damage.
Motor has thermal overload protection; let cool and push reset button if activated.
If overload repeats, stop compressor and seek qualified service.
Follow specific cautions regarding parts, electrical safety, and operation.
Ensure lubricating oil is clean and oil level is maintained as per ruler.
Examine and clean air filters monthly, or more often in dusty conditions.
Perform cleaning and oil changes at specified working hour intervals.
Diagram showing numbered components of the air compressor for reference.
Table listing parts with quantities and corresponding part numbers for ordering.
Details of the manufacturer, SGS Engineering (UK) Ltd, and the equipment.
Lists EC Council Directives and harmonized standards the compressor conforms to.
Formal declaration by Company Secretary confirming equipment conformity.
General| Brand | SGS |
|---|---|
| Model | SC24L |
| Category | Air Compressor |
| Language | English |
To Next Page
