– 5 –
CD-BA3000
OPERATION MANUAL
SETTING THE CLOCK
In this example, the clock is set for the 12-hour (AM 12:00)
system.
1 Press the ON/STAND-BY button to enter the stand-by mode.
2 Press the CLOCK button.
3 Within 5 seconds, press the MEMORY/SET button.
4 Press the TUNING/TIME ( or ) button to select the time
display mode.
“AM 12:00” →The 12-hour display will appear.
(AM 12:00 - PM 11:59)
“AM 0:00” →The 12-hour display will appear.
(AM 0:00 - PM 11:59)
“0:00” →The 24-hour display will appear.
(0:00 - 23:59)
● Note that this can only be set when the unit is first in-
stalled or it has been reset.
5 Press the MEMORY/SET button.
6 Press the TUNING/TIME ( ) button to adjust the hour.
● Press the TUNING/TIME ( ) button once to ad-
vance the time by 1 hour. Hold it down to advance con-
tinuously.
● When the 12-hour display is selected, “AM” will change
automatically to “PM”.
7 Press the MEMORY/SET button.
8 Press the TUNING/TIME ( ) button to adjust the min-
utes.
● Press the TUNING/TIME ( ) button once to ad-
vance the time by 1 minute. Hold it down to change the
time in 5 minute intervals.
● The hour setting will not advance even if minutes advance
from “59” to “00”.
9 Press the MEMORY/SET button.
● The clock starts operating from “0” second.
(Seconds are not displayed.)
And then the clock display will disappear after a few sec-
onds.
To see the time display:
Press the CLOCK button.
● The time display will appear for about 5 seconds.
Note:
● The clock display will flash on and off at the push of the
CLOCK button when the AC power supply is restored after
a power failure occurs or after the AC power lead is discon-
nected.
If this happens, follow the procedure below to change the
clock time.
To change the clock time:
1 Press the CLOCK button.
2
Within 5 seconds, press the MEMORY/SET button.
3
Perform steps 6 - 9 above.
To change the time display mode:
1 Perform steps 1 - 2 in the section “RESETTING THE MI-
CROCOMPUTER”.
2
Perform steps 1 - 9 above.
(Main unit operation)
or
or
or
or
0.2 m - 6 m
(8" - 20’)
■ Remote control
Notes concerning use:
● Replace the batteries if the operating distance is reduced or
if the operation becomes erratic.
● Periodically clean the transmitter LED on the remote con-
trol and the sensor on the main unit with a soft cloth.
● Exposing the sensor on the main unit to strong light may
interfere with operation. Change the lighting or the direction
of the unit.
● Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
PREPARATION FOR USE
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following con-
ditions:
● To erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
● If the display is not correct.
● If the operation is not correct.
1 Press the ON/STAND-BY button to enter the stand-by mode.
2 Whilst pressing down the button and the X-BASS/
DEMO button, hold down the ON/STAND-BY button for at
least 1 second.
● “CLEAR AL” will appear.
Caution:
● The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and
CD presets.
To Next Page
Loading...
Need help?
General
