: Continuous playback menu
SQ : Continuous playback (pit section)
AP : Continuous playback (groove section)
# # # # : Address
: Continuous playback (pit section)
: Continuous playback (groove section)
# # # # : Address
Continuous Playback
* When the [STOP] button is pressed in specific menu, the "TEST MODE STOP" state is set.
* In the start address set state the start address changes as follows when the [DISP] button is pressed.
0 0 3 2
H
(initial value) 0 3 C 0
H
0 7 0 0
H
0 8 A 0
H
A d 0 0 3 2
A d 0 3 C 0
DISP
DISP
A d 0 7 0 0
DISP
DISP
A d 0 8 A 0
* In the start address setting state the start address change digit changes when the [P-MODE] button is pressed.
1st digit (initial value) 2nd digit 3rd digit
A d 0 0 5 0
A d 0 0 5 0
MODE
MODE
A d 0 0 5 0
MODE
* In the continuous playback state the number of jump lines changes as follows shown
the [BASS] button is pressed.
1 (initial value) 10
1 T R
1 0 T R
BASS
BASS
1 0 0 s t p
BASS
• Continuous playback from current pickup position
: Continuous playback menu
: Start address setting
DISP
T P L A Y
A d 0 0 3 2
PLAY
S Q # # # #
A P # # # #
• Continuous playback from any address
* In the start address set state the value of selection digit changes in the range of "0h to Fh"
when the [SKIP UP/DOWN] button is pressed
* If the [P-MODE] button is pressed in the continuous playback state, the mode is changed to the B-ATT setting
state of the ATT manual adjustment.
* When the [SKIP UP] button is pressed in the continued playback mode, jump of specified
number of lines occurs in the external periphery direction.
If the key is held down jump occurs continuously (100 ms cycle).
* When the [SKIP DOWN] button is pressed in the continuous playback mode, jump of
specified number of lines occurs in the internal periphery direction.
If the key is held down, jump occurs continuously (100 ms cycle).
A d 0 9 5 0
PLAY
T P L A Y
S Q # # # #
A P # # # #
AUTO1 Practice finish?
AUTO2 Practice finish?
YES
YES
E r A D J
AUTO2 Practice
No error?
A D J. N G
NO
NO
YES
NO
0 9 5 0
H
100step
P-MODE
H B
L B
S Q # # # #
A P # # # #
: Continuous playback (pit section)
: Continuous playback (groove section)
# # # # : Address
: High-reflection pit section B-ATT (focus) setting
: Low-reflection groove section B-ATT (focus) setting
: ATT setting
: Continuous record menu
Continuous Record
* When the [STOP] button is pressed in specific condition, the "TEST MODE STOP" state is set.
* In the start address set state the start address changes as follows when the [DISP] button is pressed.
• Continuous record from the current pickup position
: Continuous record menu
: Start address setting
: Continuous record
# # # #: Address
: Continuous record
# # # #: Address
DISP
T R E C
A d 0 0 3 2
PLAY
A P # # # #
• Continuous record playback from any address
A d 0 0 3 2
0 0 3 2
H
(initial value) 0 3 C 0
H
0 7 0 0
H
0 8 A 0
H
A d 0 3 C 0
DISP
A d 0 7 0 0
DISP DISP
DISP
A d 0 8 A 0
* In the start address setting state the start address change digit changes when the [P-MODE] button is pressed.
* In the start address set state the value of selection digit changes in the range of 0h to Fh when
the [SKIP UP/DOWN] button is pressed.
* In the continuous record state and start address set state the record laser power changes in the
range of "0h to Fh" when the [VOL UP/DOWN] button is pressed. (Initial value 0DH)
A d 0 0 5 0
1st digit (initial value) 2nd digit 3rd digit
A d 0 0 5 0
MODE
A d 0 0 5 0
MODE
MODE
A d 0 9 5 0
0 9 5 0
H
PLAY
T R E C
A P # # # #
AUTO1 Practice finish?
AUTO2 Practice finish?
YES
YES
E r A D J
AUTO2 Practice
No error?
A D J. N G
NO
NO
YES
NO
Enter the EEPROM setting mode, and press the SKIP UP button.
Change the MSL setting value from 00 to 08 by using CTRL_ (control setting nenu).
(If the MSL remains in 00, no signal is recorded.)
yj y(y)
• Focus balance Adjustment mode
DISP
T-PLAY Each indication
b
# # #
PLAY
Others indication
* The focus balance adjustment mode is available only for low reflection discs.
* The RANDOM marker lights up in the focus balance adjustment mode.
* The focus balance ( ) can be changed by the VOL UP/DOWN button operation.
* If the PLAY button is pressed in the focus balance adjustment mode, the unit returns to the
continuous playback mode.
: Continuous playback menu
: Focus balance Adjustment mode
: Foucus balance
# # # : Jitter error
To Next Page
Loading...
Need help?
General
