Sharp MD-MT866H - Basic Operation: Playback Controls; Playback, Volume, and Bass Adjustment; Playback Notes and Cautions

MD-MT866H/MD-MT866W
– 25 –
: ATT manual adjustment menu
: Temperature code indication
$ $ : Temperature code
: Laser ON (play power)
: Pit section E-ATT (tracking) setting
: ATT setting
: Pit section F-ATT (tracking) setting
: ATT setting
: High reflection A-ATT (focus) setting : Low reflection A-ATT (focus) setting
: ATT setting
: TCRS ATT setting
: ATT setting
:Groove section E-ATT (tracking) setting
: ATT setting
:Groove section F-ATT (tracking) setting
: ATT setting
: Low reflection A-ATT (focus) setting
: ATT setting
: Low reflection B-ATT (focus) setting
: ATT setting
PLAY
M A N U 2
Servo ATT Manual Adjustment
T M P $ $
L O N P
SKIP UP SKIP DOWN
P E
SKIP UP SKIP DOWN
P F
SKIP UP SKIP DOWN
H A L a
SKIP UP SKIP DOWN
: High reflection B-ATT (focus) setting : Low reflection B-ATT (focus) setting
: ATT setting
H B L b
SKIP UP SKIP DOWN
G C
SKIP UP SKIP DOWN
G E
SKIP UP SKIP DOWN
G F
SKIP UP SKIP DOWN
L A
SKIP UP SKIP DOWN
L B
SKIP UP SKIP DOWN
* When the [STOP] button is pressed in specific condition, the "TEST MODE STOP" state is set. * If the [PLAY] button is pressed in the B-ATT setting state, the mode is changed to the continuous playback mode. And if the [P-MODE] button is pressed in the continuous playback state, the mode is changed to the B-ATT setting state of the ATT manual adjustment.
L b S Q # # # #
PLAY P-MODE
H B
: Continuous playback (pit section) : Continuous playback (groove section) # # # # : Address
: High-reflection pit section B-ATT (focus) setting : Low-reflection pit section B-ATT (focus) setting : Low-reflection groove section B-ATT (focus) setting
: ATT setting
L B
A P # # # #
P F
f i
E F
DISP
DISP
P E e i
E F
DISP
DISP
DISP
DISP
• LPFFINO/EFMIO measurement value
• LPFEINO/EFMIO measurement value
T C
DISP DISP
G C
H B
a b
DISP DISP
H A
• TCRSMIO measurement value
• LPFABO measurement value
* In the specific setting display state the setting change digit changes when the [P-MODE] button is pressed. * In the specific state the setting changes in the range of "0h to Fh" when the [VOL UP/DOWN] button is pressed. * If the [DISP] button is pressed, the display changes as follows.
P-MODE
P-MODE
* If the [BASS] button is pressed in the laser ON state (with no disc or the lid open), laser power changes as follows.
Playback power Record power Maximum power
BASS
BASS
BASS
L O N P
L O N R
L O N M
: EFMIO measurement value indication "REPEAT", "1" Mark lighting
: LPFFINO measurement value indication "1" Mark lighting
: Pit section F-ATT (tracking) setting : Groove section F-ATT (tracking) setting
: EFMIO measurement value indication "REPEAT", "1" Mark lighting
: LPFEINO measurement value indication "1" Mark lighting
: Pit section E-ATT (tracking) setting : Groove section E-ATT (tracking) setting
: TCRSMIO measurement value indication "1" Mark lighting
: TCRS ATT setting : LPFABO measurement value indication "1" Mark lighting
: High-reflection pit section A-ATT (focus) setting : High-reflection pit section B-ATT (focus) setting : Low-reflection pit section A-ATT (focus) setting : Low-reflection pit section B-ATT (focus) setting : Low-reflection groove section A-ATT (focus) setting : Low-reflection groove section B-ATT (focus) setting
L b
L a
L B
L A
G E
G F
1st digit (initial value) 2nd digit 3rd digit
MODE