Sharp MX-4100N - Page 179

MX-5001N SIMULATION 6 – 32
26
26-1
Purpose
Setting
Function (Purpose)
Used to set the paper exit tray (MX-TRX1).
Section
Paper exit
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key. (The set value is saved.)
This setting is required to use the paper exit tray unit (MX-TRX1).
26-2
Purpose
Setting
Function (Purpose)
Used to set the paper size of the large
capacity tray (LCC). (When the paper size
is changed, this simulation must be exe-
cuted to change the paper size in software.)
Section
Paper feed
Operation/Procedure
Select a paper size to be changed with the touch panel.
26-3
Purpose
Setting
Function (Purpose)
Used to set the specifications of the auditor
.(Setting must be made according to the
auditor use conditions.)
Section
Auditor
Operation/Procedure
Select an item to be set with the touch panel.
Item/Display Content
A 0 YES Paper exit tray : YES
1 NO Paper exit tray : NO
LCC 0 8.5 x 11
1A4
2B5
G/LBS SET 0 GRAM
1LBS
ǂǂǂ6,08/$7,21
ǂǂ12
&/26(
7(67
$8720$7,&'(9(/23(5$'-8670(17



(;(&87(
$7'(9($'-B/B. $7'(9(92B0B.
$7'(9($'-B/B& $7'(9(92B0B&
$7'(9($'-B/B0 $7'(9(92B0B0
$7'(9($'-B/B< $7'(9(92B0B<
$7'(9($'-B0B.
$7'(9($'-B0B&
$7'(9($'-B0B0
$7'(9($'-B0B<
$7'(9(92B/B.
$7'(9(92B/B&
$7'(9(92B/B0
$7'(9(92B/B<
. & 0 <
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
5,*+775$<6(783



$˖
˷ ˹
˖<(612
$˖
2.
Item/Display Content
Default
value
BUILT-IN
AUDITOR
P10 Built-in auditor mode
(standard mode) operation.
P10
EC1 EC1 mode operation
OUTSIDE
AUDITOR
NONE No external connection
vendor is used.
NONE
P VENDOR1 Coin vendor mode
(Only the copy mode can
be controlled.)
P VENDOR2 Vendor mode
communicating with the
parallel I/F (for DocuLyzer)
(Japan only)
VENDOR-EX
(*1)
Vendor I/F for EQUITRAC
VENDOR-EX
(MULTI) (*1)
VENDOR-EX + Multi job
cueing Enable mode
P OTHER NOT USED
S_VENDOR Serial vendor mode
DOC ADJ ON Support for the auditor in
document filing print
OFF
OFF No support for the auditor in
document filing print
PF ADJ ON Continuous printing is
performed in the duplex
print mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
OFF
OFF Continuous printing is not
performed in the duplex
print mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back
surface.
VENDOR
MODE (*2)
MODE1 Vendor mode 1 MODE
3
MODE2 Vendor mode 2
MODE3 Vendor mode 3
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,=(6(783





h %$
/&& ˖
*5$0 /%6
*/%66(7 ˖