Sharp MX-4100N - Page 246

MX-5001N SIMULATION 6 – 99
When the adjustment value is increased, the distance from the
paper lead edge to the image lead edge is increased. When the
adjustment value is decreased, the distance from the paper lead
edge to the image lead edge is decreased.
When the set value is changed by 1, the distance is changed by
about 0.1mm.
50-6
Purpose
Adjustment
Function (Purpose)
Used to adjust the copy image position and
the image loss. (RSPF/DSPF mode)
Section
RSPF/DSPF
Operation/Procedure
1) Select an adjustment target item with [↑] [↓] key on the touch
panel.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
[DSPF]
[RSPF]
G DENB-CS3 Tray 3 rear edge void
area adjustment
correction value
1 - 99 50
H DENB-CS4 Tray 4 rear edge void
area adjustment
correction value
1 - 99 50
I DENB-LCC LCC rear edge void aria
adjustment correction
value
1 - 99 50
J DENB-ADU ADU rear edge void aria
adjustment correction
value
1 - 99 50
K MULTI COUNT Number of print 1 - 999 1 Adjustment pattern print conditions setting
L PAPER MFT Tray
selection
Manual
paper feed
1 - 6 1 2 (CS1)
CS1 Tray 1 2
CS2 Tray 2 3
CS3 Tray 3 4
CS4 Tray 4 5
LCC LCC 6
M DUPLEX YES Duplex
print
selection
Yes 0 - 1 0 1 (NO)
NO No 1
Item/Display Content
Setting
range
Default
value
NOTE
Item/Display Content
Setting
range
Default
value
A SIDE1 Front surface
document scan
position
adjustment (CCD)
1 - 99 50
B SIDE2 Back surface
document scan
position
adjustment (CCD)
1 - 99 50
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
/($'('*($'-8670(179$/8(35,17(5



$˖
˷˹
˖'(1&
$˖
˖'(1%
%˖
˖)52175($5
&˖
˖'(1%0)7
'˖
˖'(1%&6
)˖
˖'(1%&6
(˖
˖'(1%&6
*˖
˖'(1%&6
+˖
˖'(1%/&&
,˖
˖'(1%$'8
-˖
˖08/7,&2817
.˖

˖

3$3(5&6
/˖

(;(&87( 2.
C Image
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface lead
edge image loss
amount setting
0 - 99 20
D FRONT_REAR
(SIDE1)
Front surface side
image loss amount
setting
0 - 99 20
E TRAIL_EDGE
(SIDE1)
Front surface rear
edge image loss
amount setting
0 - 99 30
F Image
loss
amount
setting
SIDE2
LEAD_EDGE
(SIDE2)
Back surface lead
edge image loss
amount setting
0 - 99 30
G FRONT_REAR
(SIDE2)
Back surface side
image loss amount
setting
0 - 99 20
H TRAIL_EDGE
(SIDE2)
Back surface rear
edge image loss
amount setting
0 - 99 20
I OFSET_SPF1 DSPF front surface
document off-
center adjustment
1 - 99 50
J OFSET_SPF2 DSPF back
surface document
off-center
adjustment
1 - 99 50
K SCAN_SPEED_SPF1 DSPF document
front surface
magnification ratio
(Sub scan)
1 - 99 50
Item/Display Content
Setting
range
Default
value
A SIDE1 Front surface
document scan
position
adjustment (CCD)
1 - 99 50
B SIDE2 Back surface
document scan
position
adjustment (CCD)
1 - 99 50
C Image
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface lead
edge image loss
amount setting
0 - 99 20
Item/Display Content
Setting
range
Default
value