How to center the data image on my Sharp PG-LW2000 Projector?
If your Sharp Projector's data image is not centered, make the necessary adjustments of each item in the “SIG-ADJ” menu. Also, the output resolution signal may be different from the one you have set.
Why am I seeing ghosting on my Sharp PG-LW2000 Projector when not in 3D mode?
If ghosting (a double image) occurs without the image appearing in 3D, check the following: * Check that you are using 3D LCD shutter glasses that support the DLP® Link™ system. * Check that the shutters on the 3D LCD shutter glasses are working properly. * Check the settings of the projector. * Check whether a signal that is not supported is being input. * If the projector is connected to a computer for 3D image playback, check that a stereoscopically-enabled application is being used. * Check that there are no obstructions between the screen and the 3D LCD shutter glasses. * Check whether there is a source of high intensity lighting nearby. * Check whether two or more projectors are projecting 3D images at the same time.
Why does the lamp on my Sharp PG-LW2000 Projector take so long to turn on?
The lamp will eventually need to be changed. While the remaining lamp life draws to a close, replace the lamp.
Why does my Sharp Projector make unusual sounds from the cabinet?
If you hear an unusual sound occasionally from the cabinet of your Sharp Projector and the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.
Why do 3D images flicker on my Sharp PG-LW2000 Projector?
If you are watching 3D images and they flicker, turn off the lights and block any ambient light.
Why is my Sharp Projector picture green?
If your Sharp Projector picture is green on COMPUTER (YPbPr)/ HDMI (YPbPr), change the input signal type setting.
Why is the picture on my Sharp PG-LW2000 too bright and whitish?
If your Sharp Projector displays a picture that is too bright and whitish, ensure that the image adjustments are correctly set.
Why does the image on my Sharp PG-LW2000 sometimes flicker?
If the image from your Sharp Projector sometimes flickers, check that the cables are correctly connected to the projector and that the connected equipment is working properly. If flickering happens frequently, replace the lamp.
What to do if Sharp Projector lamp doesn't light up?
If your Sharp Projector lamp does not light up after turning it on and the lamp indicator is illuminating in red, replace the lamp.
How to troubleshoot a Sharp PG-LW2000 Projector that has no picture, no sound, and won't start?
If your Sharp Projector shows no picture and no sound, and doesn't start, here's what to check: * Ensure the projector's power cord is securely plugged into the wall outlet. * Verify that connected external devices are powered on. * Confirm the correct input mode is selected on the projector. * Deactivate the AV Mute function if it's enabled. * Check all cables for correct connections to the projector. * Replace the remote control battery if it's depleted. * If using a notebook, ensure external output is enabled. * Make sure the lamp unit cover is correctly installed.
Explains projector and computer connection and setup using one example.
Instructions for connecting various external devices like computers and video equipment.
Covers turning the projector on/off and initial image projection adjustments.
Explains use of pointer, spot, Eco+Quiet, and other remote functions.
Covers cleaning, maintenance indicators, and lamp replacement procedures.
General| Brightness | 2000 ANSI Lumens |
|---|---|
| Contrast Ratio | 2000:1 |
| Weight | 2.5 kg |
| Aspect Ratio | 16:10 |
| Display Type | DLP |
| Projection Size | 30 to 300 inches |
| Output Ports | Audio Out |
| Resolution | 1280 x 800 |
| Input Ports | Composite Video, S-Video |
To Next Page