EasyManua.ls Logo

Sharp PN-465U - Important Information and Safety

Sharp PN-465U
92 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
PN-465U OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1 – 1
CHAPTER 1. OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1. SPECIFICATIONS
*1 Cannot be used simultaneously.
*2 Does not support plug and play.
*3 Connection is allowed with an HDCP-compatible device only.
Does not support Repeater control function.
DIMENSIONAL DRAWINGS
Note: That the values shown are approximate values.
When mounting the monitor, be sure to use a wall-mount / ceiling-mount
bracket they comply with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose
holding may cause the product to fall, resulting in serious personal inju-
ries as well as damage to the product. The screw and hole should come
together with over 5/16 inch (8 mm) length of thread. SHARP recom-
mends using mounting interface that comply with UL1678 standard.
COMPATIBLE SIGNAL TIMING (PC)
Model PN-465U
LCD element 46” wide (116.8 cm diagonal)
ASV low-reflection black TFT LCD
Max. resolution
(pixels)
1920
× 1080
Max. colors 16.77 M colors (8 bits/color)
Pixel pitch 0.53025mm (H)
× 0.53025mm (V)
Viewing angle 176° right/left/up/down (contrast ratio >
10)
Screen active
area inch (mm)
40-1/16
× 22-9/16 (1018.1 × 572.7)
Computer input
signal
Digital (DVI 1.0 standard-compliant),
Analog RGB (0.7Vp-p) [75]
Sync
signal
Horizontal/vertical separate
(TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video signal
system
NTSC (3.58MHz)
Plug and play VESA DDC2B
Power
management
VESA DPMS, DVI DMPM
Input terminals PC/AV Digital DVI-D 24 pin
(HDCP compatible)
× 1
PC Analog Mini D-sub 15 pin,
3 rows
× 1, BNC
*1*2
× 1
Audio 3.5 mm mini stereo jack
× 1
AV Composite
video
BNC
× 1
Component
BNC (Y, Cb/Pb, Cr/Pr)
*
1
×
1
Audio RCA pin (L/R) × 1
Serial (RS-232C) D-sub 9 pin
× 1
Output terminals PC/AV Digital DVI-D 24 pin
× 1
*3
Audio RCA pin (L/R) × 1
Serial (RS-232C) D-sub 9 pin
× 1
Speaker 7W
+ 7W [6]
Power
requirement
AC 120 V, 60 Hz
Operating
temperature
32°F to 104°F (0°C to 40°C)
Operating
humidity
20% to 80% (no condensation)
Power
consumption
266W (Input signal waiting mode: 6.5W,
Standby mode: 3.5W)
Dimensions
inch (mm)
Approx. 43-13/16
× 5-1/2 × 25-7/8
(1,113
× 140 × 657) (excluding protrusions)
Weight lbs. (kg) Approx. 78.3 (35.5)
(excluding the temporarystand)
Screen resolution Hsync Vsync
Dot
frequency
Analog
signal
Digital
signal
VESA 640
× 480 31.5kHz 60Hz 25.175MHz oo
37.9kHz 72Hz 31.5MHz oo
37.5kHz 75Hz 31.5MHz oo
800
× 600 35.1kHz 56Hz 36.0MHz o
-
37.9kHz 60Hz 40.0MHz oo
48.1kHz 72Hz 50.0MHz oo
46.9kHz 75Hz 49.5MHz oo
848
× 480 31.0kHz 60Hz 33.75MHz oo
1024
× 768 48.4kHz 60Hz 65.0MHz oo
56.5kHz 70Hz 75.0MHz oo
60.0kHz 75Hz 78.75MHz oo
1152
× 864 67.5kHz 75Hz 108.0MHz oo
1280
× 768 47.8kHz 60Hz 79.5MHz oo
60.3kHz 75Hz 102.25MHz oo
1280
× 960 60.0kHz 60Hz 108.0MHz oo
Opening height
(22-11/16 [576])
Opening width (40-1/4 [1023])
7-7/8
[200]
7-7/8
[200]
7-7/8 [200] 9 [228.5]
3-3/8
[87]
5-1/2 [140]
2-1/16 [52]
15/16 [24]
34-3/4 [882]
43-13/16 [1113]
25-7/8 [657]
22-7/8 [581]
Unit: inch [mm]
VESA holes

Other manuals for Sharp PN-465U

Related product manuals