PN-465U CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTION
2 – 22
(1)-2. White Balance setting value write
The White Balance setting values are written in the following proce-
dures.
Since White Balance is set individually for the PC system input mode
and the AV system input mode, write the set data to each of them.
[Operating procedures]
1) Press [INPUT] button to select the input mode to write the setting
data.
• To write the setting data of the PC system input mode, select
either of PC1 DIGITAL, PC2 ANALOG, or PC3 ANALOG mode.
• To write the setting data of the AV system input mode, select
either of AV1 DIGITAL, AV2 COMPONENT, or AV3 VIDEO mode.
2) Any image is displayed on the screen.
3) SERVICE MENU2 is displayed.
4) Select “WHITE BALANCE SETTING” with [ 2 ] [ 4 ] buttons, and
press [3] button.
The WHITE BALANCE SETTING menu is displayed.
In the PC system input mode, “(PC)” is displayed as the menu title.
In the AV system input mode, “(AV)” is displayed.
5) Check to confirm that the PATTERN is “9000K”.
If it is “6500K”, select “PATTERN” with [ 2 ] [ 4 ] buttons and press
[3] button to set to “9000K”.
6) Select “LEVEL” with [ 2 ] [ 4 ] buttons and press [3] button. The
LEVEL menu is displayed.
7) Set the data written down previously. Select LEVEL1 ~ LEVEL6
with [ 2 ] [ 4 ] buttons and adjust the value with [1] [3] buttons.
8) Check to confirm that the set values of LEVEL1 - LEVEL6 are prop-
erly adjusted.
9) Select “OK” with [ 2 ] [ 4 ] buttons, and press [MENU] button.
The setting is saved and the display returns to the WHITE BAL-
ANCE SETTING menu.
10) Set the values L1 - L6 of R, L1 - L6 of G, and L1 - L6 of B to the val-
ues previously written down. Select L1 - L6 with [ 2 ] [ 4 ] buttons,
select R/G/B with [1] [3] buttons, and adjust the set values with
[ 2 ] [ 4 ] buttons.
11) Select “L*” at the left end with [1] [3] buttons, and repeat the
operation.
12) Check to confirm that all the set values are set properly.
13) Select “OK” with [ 2 ] [ 4 ] buttons, and press [MENU] button.
The set data are saved and the WHITE BALANCE SETTING menu
is terminated.
* Since White Balance is set individually for the PC system input
mode and the AV system input mode, write the set data to each
of them.
14) Read the set data of WHITE BALANCE and check to confirm that
all the values are properly set.
(2) When replacing the panel or when an old PWB does
not operate
Reset the setting to return to the initial state by executing the following
procedures.
Since White Balance is set individually for the PC system input mode
and the AV system input mode, reset to each the set data .
[Operating procedures]
1) Press [INPUT] button to select the input mode to reset the setting
data.
• To reset the setting data of the PC system input mode, select
either of PC1 DIGITAL, PC2 ANALOG, or PC3 ANALOG mode.
• To reset the setting data of the AV system input mode, select
either of AV1 DIGITAL, AV2 COMPONENT, or AV3 VIDEO mode.
2) Any image is displayed on the screen.
3) SERVICE MENU2 is displayed.
4) Select “WHITE BALANCE SETTING” with [ 2 ] [ 4 ] buttons, and
press [3] button.
The WHITE BALANCE SETTING menu is displayed.
In the PC system input mode, “(PC)” is displayed as the menu title.
In the AV system input mode, “(AV)” is displayed.
5) Check to confirm that the PATTERN is “9000K”.
If it is “6500K”, select “PATTERN” with [ 2 ] [ 4 ] buttons and press
[3] button to set to “9000K”.
6) Select “LEVEL” with [ 2 ] [ 4 ] buttons and press [3] button. The
LEVEL menu is displayed.
7) Select “RESET” with [ 2 ] [ 4 ] [1] [3] buttons and press [MENU]
button.
8) Check to confirm that the set value is changed as shown below.
• Initial values of the PC system input mode
• Initial values of the AV system input mode
9) Select “OK” with [1] [3] buttons, and press [MENU] button.
The display returns to the WHITE BALANCE SETTING menu.
10) Select “RESET” with [ 2 ] [ 4 ] [1] [3] buttons and press [MENU]
button.
11) Check to confirm that all the set value is changed as shown below.
• Initial values of the PC system input mode
LEVEL (PC)
LEVEL1
LEVEL2
LEVEL3
LEVEL4
LEVEL5
LEVEL6
< 48 >
< 88 >
< 132 >
< 164 >
< 200 >
< 255 >
OK CANCEL RESET
LEVEL (AV)
LEVEL1
LEVEL2
LEVEL3
LEVEL4
LEVEL5
LEVEL6
< 48 >
< 85 >
< 128 >
< 160 >
< 196 >
< 255 >
OK CANCEL RESET
WHITE BALANCE SETTING (PC)
PATTERN
< 9000 K >
LEVEL =>
L1 R: 208 G: 230 B: 210
L2 R: 209 G: 230 B: 214
L3 R: 210 G: 230 B: 216
L4 R: 212 G: 230 B: 217
L5 R: 213 G: 230 B: 219
L6 R: 242 G: 255 B: 248
OK CANCEL RESET
To Next Page
Loading...
