EasyManua.ls Logo

Sharp PN-S525 - Specifications

Sharp PN-S525
112 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
16
E
DPMS: Display Power Management Signaling
DPMS Screen
Power
consumption
Hsync Vsync
ON STATE Display 275W Yes Yes
STANDBY
No
display
12W*
No Yes
SUSPEND Yes No
OFF STATE No No
Specications
n
Product Specications
Model PN-S525
LCD element 52" wide (132.2 cm diagonal) ASV low-reflection black TFT LCD
Max. resolution (pixels) 1920 x 1080
Max. colors 16.77 M colors (8 bits/color)
Pixel pitch 0.600 mm (H) x 0.600 mm (V)
Viewing angle 176° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm) 45-3/8 x 25-1/2 (1152.0 x 648.0)
Computer input signal Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 ]
Sync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system PAL, PAL-60, SECAM, NTSC (3.58 MHz), NTSC (4.43 MHz)
Plug and play VESA DDC2B
Power management VESA DPMS, DVI DMPM
Input terminals PC/AV Digital DVI-D 24 pin (HDCP compatible) x 1
HDMI x 1
PC Analog Mini D-sub 15 pin, 3 rows x 1
BNC
*1*2
x 1
Audio 3.5 mm mini stereo jack x 1
AV Composite video BNC x 1
S-video x 1
Component BNC (Y, Cb/Pb, Cr/Pr)
*1
x 1
Audio RCA pin (L/R) x 1
Serial (RS-232C) D-sub 9 pin x 1
Output terminals PC/AV Digital DVI-D 24 pin x 1
Audio RCA pin (L/R) x 1
Serial (RS-232C) D-sub 9 pin x 1
Speaker 7 W + 7 W [6 ]
LAN terminal 10 BASE-T/100 BASE-TX
Power requirement AC 100 V - 240 V, 50/60 Hz
Operating temperature 32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption 275 W (Input signal waiting mode: 12 W
*3
, Standby mode: 2.0 W
*4
)
Dimensions inch (mm) Approx. 49-3/8 x 5-7/8 x 29-3/16 (1,254 x 149 x 742) (excluding protrusions)
Weight lbs. (kg) Approx. 86.0 (39) (excluding the temporary stand)
*1 Cannot be used simultaneously.
*2 Does not support plug and play.
*3 WhenAUTOINPUTCHANGEissettoOFF.
*4 WhenSTANDBYMODEissettoLOWPOWER,LANandSCHEDULEarenotused.WhenSTANDBYMODEissettoSTANDARD,12W.
Asapartofourpolicyofcontinuousimprovement,SHARPreservestherighttomakedesignandspecicationchangesforproductimprovement
withoutpriornotice.Theperformancespecicationguresindicatedarenominalvaluesofproductionunits.Theremaybesomedeviationsfrom
these values in individual units.
n
Power management
ThismonitorconformstoVESADPMSandDVIDMPM.Bothyourvideocardandcomputermustsupportthesamestandardin
order for the monitor’s power management function to work.
DMPM: Digital Monitor Power Management
DMPM Screen
Power
consumption
Monitor ON Display 275W
Active OFF No display 12W*
* WhenAUTOINPUTCHANGEissettoOFF.

Table of Contents

Other manuals for Sharp PN-S525

Related product manuals