.,.
SF–7700
SF–7750
@ Set tray angles L and R firmlyagainst the bottomof the SADF
: tray. S~re the angles with the provided*rews (M4x6 with
ny~ washers).
\-.
1
(an = 2 digitdafs num~r)~e ready indi~tor willgOOUtand
fhsWwtitasettingwill ~s~n in~e~pyquanti~display.
NOTE: * sure notto ~ti the size det@ion h&ss behindthe
rear abine~
3) Looalmodeprograming
Make settingsafter instdtafionon the -y machine~ptete.
NOTE: The system will not futiion properfyif the oorr~ setting
are not made.
O~ON SELE~ON AND COUNTER MODE S~NG.
Make the follwing adjustmentswhen a semi-automaticdmument
feeder (SF-) or sofier (SF413) is instdied or when changing
either the tot~ Writer or maintenme anter mode from single
-nt to double ant or from dou~e to single.
IMetfsod]
@ Turn the mpy machine ~er ON.
@ Push the followingto ex~te test ~mand 78. C + P + O+
P +~+~+ Psw
When the ready lamp lights the current stored parameter is
displayed.
3-5
@ Pushthe clear key to @repletethe setting.
4) Installationadjustments
A. Trsn~ unh d~
t M dtsr speed Sdjustrnem
(
@ Ck the transport*on.
@ Use the keys and keyp@ on the operationpanel and enterthe
fdtiing key aeque~.
c + P 40 + P +@+@4
Psw.
%
dooumentfeed rollerwill turn for approximately1-2 sm.,
@ the @U-t feed irrdimtoron the panel will blinktwo or
three times. This oompletesrollerspeed adjustment.
Se sure to adlust the transportunit duument feed roller speed
beforeadjustingthe dmrnerrt f~ sensorsensitivity.
6.Trsn~un~d~~ rn~~r~~ju~
~ Close the transport-n.
..4
@ Set a whitesheet of ~ paper in the SADF tray.
@ Now use the keys and keypadon the.operafionpanel and enter
the folfowingkey,
%
ueme.
c + P 40 + P 44
-g+ Psw.
~The
sheetof p-r willbfsd and immadiate&diwharged. The
dmment feed indtitor on the rightside of the panel willblink
two or three times. ~ oornpletesthe adjusfmsnt.
NOTE: If the paper is ~t fed, or if the originalreminderindictor
lights due to a pro~em in tran~rtati~n, repeat tie
prtiure fromstep @-@.
C. O~instl S*
dst-or adlu-t (onSF-~W only).
6
Adlustthe ortginalsize det~or on the apy machineas follows.
@ Close the franspons~on.
@ Use the keys and keypadon
theoperationPaneland enterthe
fottoting key stierr~.
c + p -0 ~ .P 4@-~+ Psw.
@ Pressthe printbutton(PS~ onm more.
@ Open the trq ~iorr.
@ Set an 1l”xIT ,(M) White Page m the frOntedge of the
dtiment glass so that it wpfetdy ~vers the originalsize
detmors.
@ Close the transport~.
@ Pm the pdrtfbuttononoa me.
(
Y
.
[
i
/
.
This ~plet~ adlusfm~t of the originalsize det~tor
To Next Page
Loading...
