SSC3088AS
14
Error Code list
error display
details of error check timing application menu error condition note check item change parts
CODE(04)
oven temperature
is high.
After 1sec.
fermentation
defrost
sterilization
low temp. steam
oven temperature is too
high
fermentation mode
over ECh bit error
under C0h bit cancel
１．Check the relay welding
２．Check the oven thermistor
３．Check the harness of the CN-B and
thermistor
１．Change the relay board
２．Chenge the oven thermistor
３．Change the control harness
CODE(0A)
shortage of Water immediately
steam
water oven
water grill
Water tank is empty when
water is ne
cessary to
operate.
In the case of water shortage even though
there is water in the water tank.
Check water.
1
．When there is no water ：change the
pump
。
２．When the pump is OK：change the engine
CODE(07)
shortage of Water
（
It is possible to
restart
）
After cook
sterilization
Water tank is empty during
sterilization mode.
CODE(08)
shortage of Water
（
sterillization
mode restarts
）
After cook
sterilization
4 minutes passed without
restart after (CODE07)"
appeared.
CODE(0F)
water tank is
frozen
immediately
steam
water oven
water grill
engine heater t
em
perature
is too low.
under 0Fh bit
In the case of an error when at the room
temperature
１．Change oven thermistor
２．Change relay board
CODE(0C)
dew tray error After cook
steam
water oven
water grill
Dew tray is not set when
cook is started.
Check the wiring of the dew tray SW.
Check the dew tray. Check the lever SW.
Check to ensure SW is pushed. Check
the hooks (3ea) of the dew tray. Check to
ensure there is no disconnection from the
dew tray SW.
If the SW is NG: Change the SW. If the lever of
SW id NG : Change the lever. If the hook is NG
: Change the Dew tray
. If the ho
lder of SW is
NG : Change the holder.
CODE(0B)
No water tank
during water drain
After water
drain
water drain
Water tank is not set at
water drain.
In the case of error, even though the Tank
is in. Check the tank to ensure SW is not
disconnect. Check CN-B of the relay
board and tank SW.
If SW is NG : Change SW. If SW hook of the
tank cover is NG: Change the tank cover. If the
board and SW are NG : Change the control
harness.
CODE(0D)
No water tank
during cook using
water
After cook
steam
water oven
water grill
Water tank is not set at
cook using wate
r.
In the
case of error, eventhough the tank
is in. check the tank SW to ensure that
SW is not disconnect.
If SW is NG : Change SW. If SW hook of the
tank cover is NG: Change the tank cover. If the
board and SW are NG : Change the control
harness.
CODE(0E)
water tank is
removed
After cook
Water drain
steam
water oven
water grill
Water tank is removed for 5
seconds during cook using
water.
CODE(11)
Oven thermistor
error
immediately all menu
oven thermistor is short or
open.
Temperature in oven is too
high.
open
fermentation mode
under 08h bit error
short
oven mode
over FBh bit error
Check the wiring of the oven thermistor.
Check the wiring of the oven thermistor
control harness and CN-B relay board.
If the thermistor is NG : Change the thermistor
If the relay board is NG : Change relay board
If the oven thermistor control harness and relay
board are NG : Change the harness.
CODE(14)
Door thermistor
error
immediately all menu
Door thermistor is short or
open.
open
under 03h bit error
short
over FDh bit error
Change DISPLAY board
CODE(15)
engine heater
error
always all menu
engine heater temperature
is too high.
over F8h bit error
Check the sensor of the engine WL.
Check the RY5 of the relay board.
Change the engine. Change the board and also
change the engine thermistor at the same time.
CODE(16)
Door fan error
always all menu
when the temperature
inside door is higher than
limit, bec
ause malfunction
occurred in Door fan.
over 8Bh bit and over
2sec continue error
Check the rotation of the door fan. Use a
paper. Check the wiring. Check
the wiring of the door fan.
Change the door fan. Change the door
board.
CODE(17)
Relay monitor
error
always all menu
micro and each heater
relay both operated
or when off cycle heater
relay operated
Check the relay board of the oven
RY2/3/4/5.
Change Relay board.
CODE(18)
SH Damper error After cook
Check the harness of the SH damper
Motor and SW operation. Check the SH
duct damper operation.
Change the SW motor of the harness or
board
If the SH damper or the SH duct is NG :
Change oven.
CODE(1C)
engine thermistor
error
After cook all menu Engine thermistor is open. under 08h bit error
Check the siring of engine thermistor and
thermistor.
Check the CN-B of control harness and
termistor terminal.
Change the harness of the termistor or board.
CODE(1D)
Pump error
during water
drain
water drain
Water cannot drain away
from engine.
(Pump or tube is broken.)
Check allocation at the time of drainage.
Check WL sensor is open.
If allocation is NG: Change the motor.
If WLsensor is continuiting display: Change
the
engine
CODE(1E)
EEPROM error on test mode short check program
EERROM Read data is not
same as EEPROM write
data.
Change the DISPLAY board.
all menu
To Next Page
Loading...
Need help?
General