VL-PD3S/H/E
VL-PD3S/H/E
8-6
393
431
420
357
390
356
394
458
381
397
352
383
455
397
351
392
354
383
384
382a
382b
382b
385
Swing arm release
lever fixing screw M
Swing arm
release lever
Swing arm
release SPR.
(2) T roller upper
flange
(2) Tu pole
(3) Pinch lever
return SPR.
(4) Pinch lever Ass'y
(5) L
(5) T spring
hanging
ANG
(8) T roller upper
flange
(8) S guide
sleeve
(5) B
(7) K
(5) K
(6) F
(6) T roller upper flange
(6) T roller Ass'y
(6) T roller inner
(6) T roller bottom flange
(6) Guide adjustment SPR.
(6) Tension arm Ass'y
T arm SPR.
(7) C
(7) Tension band
Ass'y
F
F
(1) Tu guide
arm SPR.
(2) Tu guide
arm Ass'y
(2) Guide adjustment
SPR.
(2) T roller bottom
flange
Grease
Item
Tightening torque
Quantity
B S Tight · M1.4 x L2 40mN·m 1
D Special screw · 40mN·m 4
M1.4 x L1.6
8-5-3. Main chassis assembly and slide chassis assembly assembling method
(1) Set the L/S mode (see the figure below).
(2) Insert the slide chassis side operation pins (
1
tension arm,
2
Tu guide arm,
3
pinch lever) in the position shown below at the
main chassis side, move the slide chassis in the arrow direction, using
A
to
E
as guides, insert the loading lever operation pin
into the groove of slide chassis, and install with the 4 screws.
Item
Tightening torque
Quantity
I CWø0.7-ø1.8-t0.1 1
N
Type 1 minuteness ·
40mN·m 1
M1.4 x L1
Item
Tightening torque
Quantity
D Special screw · 40mN·m 2
M1.4 x L1.6
O Special screw · 40mN·m 1
M1.4 x L2
500
501
326
Cap FPC cover
(1) D
(1) O
(1) D
(1) Head amplifier P.W.B. unit
H/A FPC shield plate
Through the groove in the cassette control.
Note1) Be careful not to scratch or dent in
the parts ( 381, 382, 383, 384, and
455 ), be careful not to deform the
tension band in handling it.
Note2) Be careful not to deform to tightening
the 382a coat the Screw lock to the
point of shaft.
Item
Tightening torque
Quantity
B S Tight · M1.4 x L2 1
C CWø1.2-ø3-t0.25 1
F CWø0.7-ø2.2-t0.25 3
L Type 2 minuteness
·
40mN·m 1
M1.4 x L1
K
Special head screw ·
40mN·m 2
M1.4 x L2
M
Special screw with step
· 40mN·m 1
M1.4 x L1
B
1
4
A
D
3
2
C
E
D
D
D
D
B
Assembly Mode
• Numbers before part names
are given as a guide to the
order of assembly.
• When treating the sensor
FPC wire, pay attention to
the part A shown in Fig. 6.
• Oil application place is
shown in Fig. 5.
* 438 Tightening torque
70 ± 7mN·m
(0.7 ± 0.07kg·cm)
438
355
398
470
377
313
(3) FPC cover
(2) N
(4) Drum Ass'y
(2) Reel cover
Ass'y
(1) I
(1) Swing arm Ass'y
(4) Drum fixing SPR
(4) Drum installation screw
Oil
To Next Page
Loading...
